PGE Tuning Lab

BMW EWS3 immobiliser faults on the E46 and the E39

A key that turns and does not crank, or cranks and does not fire, on an E46 or E39 sends you to the EWS3 behind the glovebox. The unit reads the key through a ring antenna around the lock, and it sends the start enable to the engine unit. The antenna and the supplies are measured before the unit is opened.

The key turns and nothing happens

The owner turns the key and the dash lights up, and the starter does nothing at all. That is the EWS3 refusing the key, because the unit controls the start enable as well as the code to the engine. Ask whether any key ever works now and whether the fault arrived after a lock or a dash repair. A lock that has been replaced leaves the antenna loose on its mount, and a dash that has been out leaves the unit connector half home.

If the engine cranks and does not fire, the key was accepted and the disagreement sits between the unit and the engine unit. The two cases are repaired in different places, so the first question to the owner is whether the engine turns over. That answer sets the whole order of the tests.

Reading the immobiliser values

Open the immobiliser address and read the live values with the key in the lock. The unit should report a key present and then a key accepted, followed by a start enable, and those values together describe how far the sequence has gone. Write them down before you clear anything.

A unit that reports no key with a known good key in the lock points at the antenna or at its wiring. A unit that reports a key present and refused has the key data to blame, and the key list is read next. A unit that gives the enable while the starter stays silent has a fault on the start relay circuit.

The ring antenna and its resistance

The antenna is a coil around the ignition lock and its plug sits behind the column shroud. Disconnect it and measure the resistance across the two pins with the unit unplugged. A coil that reads open has a broken winding, and a coil that reads far from the value on a known good car has a shorted turn. Compare it with the same coil on a car that starts, because a coil that reads slightly low is still a suspect.

Flex the antenna lead while the meter is connected and watch the reading, because a value that jumps as the lead moves is the fault you are hunting for. A coil that is loose on the lock reads a key at two centimetres and misses it at five, which is why a key that works when held close is a clue rather than a coincidence.

Supply and ground at the EWS

Measure the permanent feed at the unit connector with the ignition off and the battery negative post as your reference. Then measure the ignition feed with the key on. Both should read battery level, and a feed that sags points at the fuse box rather than at the unit itself. The unit shares its fuse with the interior lamps on some cars, so a blown fuse shows as a dark cabin and a silent starter at the same moment.

Measure the ground pins against the battery post on the millivolt range with the plug fitted. A drop above about fifty millivolts disturbs the reader and gives a key that is accepted on one attempt and refused on the next. Clean the stud and repeat both the ground drop and the key test afterwards.

The rolling code and lost sync

The unit and the engine unit share a code that changes every time the engine starts, and the two must stay in step for the engine to fire. A unit that was swapped, or a code that was written back to an older value, leaves the pair out of step and the engine cranks without firing.

This is read in the live values as a key that is accepted with no start enable to the engine. The car reports it as an authorisation entry in the engine unit, and that entry is read before the coils are touched. A pair that is out of step is aligned with the diagnostic equipment and a stable supply on the battery.

The start enable wire

The unit sends the enable to the starter relay on a single wire, and a break in that wire leaves the car silent with a key that the unit has accepted. Measure the wire from the unit plug to the relay socket with the meter on continuity and the battery disconnected.

Then measure the voltage on that wire at the relay socket while the key is turned, because a signal that appears for a moment and falls away describes a unit that is trying and a relay that is not answering. A relay that clicks and does not crank has its own fault, and the unit is cleared. Check that relay with a bulb across its output, since a click only proves that the coil inside it moved.

A second key and a spare unit

Try the second key before anything is opened, and do it with the keys well apart so the car cannot read both at once. A different result from the second key separates a worn transponder from a unit fault, and it saves an unnecessary repair on a unit that was working.

A used unit carries the code of the car it came from, and it will not start another car until the pair is aligned and the keys are written. Save the data from the old unit before it leaves the car, because a list that is lost with the unit cannot be rebuilt from the keys in the owner pocket. Write the part number from the old unit beside the new one, since two units that look alike are not always interchangeable.

What confirms the fault

The EWS3 is the fault when its supplies hold under load, the ground drop is low, the antenna measures correctly, the second key behaves the same way, and the unit refuses a key it can read. Those results together leave the unit as the repair, and each one is written down. A car that reads a key and refuses to crank has an enable problem rather than a key problem, and the wire to the relay is measured next.

A unit that reads a key and gives no enable has an internal fault or a code that no longer matches, and the pair is aligned before the board is opened. A unit that reads no key at all with a good antenna has a reader fault inside it, and that is found on the bench with a known key held against the coil.

Try the second key before the column shroud comes off, because a key with a worn transponder behaves exactly like a unit that has failed, and the second key answers that question in a minute. Then measure the antenna coil and the ground drop at the unit. A car that reads no key with a good coil has a reader fault that a bench test will confirm. Write the key value and the coil resistance on the sheet, then the start enable.

What is measured on an EWS3 that refuses the key
SymptomLikely causeWhat is measured
Key turns, starter silentKey refused by the unitKey present and key accepted in live values
Key works only when held closeWorn antenna coilCoil resistance and reading distance
Cranks and does not fireCode out of step with the engine unitStart enable value in both units
Key accepted, starter silentStart enable wire or relayVoltage at the relay socket during the turn

Frequently Asked Questions

Why does the engine crank but not fire?

The starter is enabled on a different path from the engine code, so a pair that is out of step still turns the engine and withholds the spark. The enable values in both units show the disagreement.

Can the immobiliser be bypassed?

The unit is repaired or the pair is aligned, and a bypass leaves the car without its theft protection. The supplies and the antenna are measured first so a simple fault is not missed.

Does a flat battery cause this?

A supply that falls away during a write leaves the code out of step, and the engine then cranks without firing. The entries in both units are read before anything is written.

What is checked after a replacement unit?

The pair is aligned, the keys are written and each one is tested with the car locked and unlocked between them. The start enable is read on each key so a later refusal is caught.

Related Services