A BMW CAS repair starts with the second key, because a car that accepts one key and refuses the other has a key problem and not a unit problem. If both keys fail, you measure the supply at the CAS connector and the reader coil before the unit is removed. On the bench the file is saved before anything else happens.
The CAS unit keeps the list of learned keys and the security data that allows the engine to start, so any work on it changes how the car answers a key. When the key is not accepted the starter gets no command and the immobiliser lamp stays on. Nothing else on the car is affected, which narrows the check.
Read the codes from the unit, then look at whether the key was rejected or whether the link to the network dropped. A rejection is stored differently from a communication loss, and the two lead to different measurements. Write both on the sheet before you open the housing.
CAS2 and CAS3 arrive with a car that sometimes starts and sometimes stays silent, usually after a period of standing. The key is read on one attempt and ignored on the next, which points to an unstable contact on the reader coil. Check the coil around the barrel and measure continuity on its wires up to the unit.
A coil with a rubbed insulation gives symptoms that appear when the key is moved in the barrel, and the fault follows the movement rather than the temperature. With the coil ruled out, read the unit on the bench from a stabilised supply and save the file. Then inspect the solder around the connector.
CAS4 and CAS4+ hold their security data in a memory that needs equipment prepared for it, so reading is done on the bench with a stable supply and no voltage steps. The car arrives with a start that stops after a second and with the immobiliser lamp on. Confirm first that the unit answers the tester at all.
An unstable supply during reading damages the result rather than the unit, and the file that comes out is unusable. Set the supply, wait for the current to settle, then read. Check the file against the key list before you write anything, because a partial read looks complete in the software.
The electric lock on the column releases when the CAS accepts the key, so a lock that stays engaged with a good key points at the lock or at its command. Listen for the motor at the moment the key is inserted, then measure the supply at the lock connector. No sound and a full supply means the lock itself.
A lock that clicks and stays engaged has a mechanical fault inside it, and forcing the wheel damages the column. The lock is often disabled in software when the column is replaced, and that step changes what the car does at every start. It is recorded on the job sheet.
Feed the unit at 13.5 V and let the current settle before the read starts, then save the file with the job number and the chassis number in its name, so a later visit finds it without a search. Keep a second copy away from the working machine, because a file lost during a write leaves the car with no key at all.
After the read, the key list is printed and compared with the keys the customer brought. A list with free slots and an original key means a new key can be added in a short visit. A list that was rewritten by earlier work changes the order of everything that follows.
A replacement needs the same part number, and the saved file is written into it before the unit goes on the car. The key list travels with the file, so the existing keys keep working. A unit from another car without the transfer leaves the car unable to start.
After fitting, each key is tested with the car locked and unlocked between attempts, and the starter is operated with the brake pressed. The immobiliser lamp is watched through the whole sequence, because it flickers on a unit that is still learning.
The keys are checked one at a time and the result is written for each one, so the customer knows which key is trusted and which is not. A key with a dead battery in the remote still starts the car, because the transponder does not need it. That distinction is explained before the car is collected.
A spare key made at the same visit saves the long procedure later, and it is offered while the unit is already on the bench. The new key is learned and then tested the same way as the others.
Put the part number, the chassis number, the build year and the series letter on the parcel, and add the codes as the tester printed them. Say whether both keys fail or only one, because that single fact changes the bench plan.
Describe what the car does when the key is inserted and whether the column lock makes a sound. A photograph of the dash with the message on it helps. Keep the key with the unit if the customer agrees, and pack the unit so the connector is protected.
With CAS2 and CAS3 the second key is the fastest test: if the second key starts the car, the fault is in the first key or its coil, and the module stays untouched. Note whether the steering lock releases with a delay, because a slow release before start points at the lock motor, not at the key reader.
| Symptom | Module or code | What is measured |
|---|---|---|
| Starts on one attempt and not the next | CAS2, CAS3 | Reader coil continuity and supply at the unit |
| Starts and stops after one second | CAS4, CAS4+ | Data read on the bench with a stable supply |
| Key accepted, column stays locked | Steering lock | Supply at the lock and motor sound |
| One key works, the second is refused | CAS3, CAS4 | Key list against the keys presented |
Yes, when it still communicates on the bench with a stable supply. The file is saved before the work, and the key list is compared with the keys you bring.
It is a separate unit that the CAS commands, so it is tested on its own. A lock with a full supply and no motor sound is the lock, not the CAS.
They do when the saved file is written into the replacement, because the key list travels with it. Each key is then tested with the car locked and unlocked.
Then the data is rebuilt from the car with the equipment prepared for that memory, which takes longer and is explained before it starts.