A BMW that unlocks and then refuses to crank, with the steering lock clicking but not releasing, puts the CAS4 in the middle of the fault. The unit holds the key list and drives the lock, so two very different faults look the same from the driver seat. The second key test separates them before anything is opened.
The car opens on the remote and the cluster lights up, then the starter does nothing and the lock stays where it was. Sometimes a message appears on the screen and sometimes nothing does, which makes the fault look random. Ask what changed before it started.
Ask specifically whether a second key was tried and whether the car was jump started, because each answer moves the fault to a different place. A car that worked with one key and stopped working after the battery went flat is not the same case as one that never accepted the key at all.
Put the second key in the car and try to start it before you open any panel. A different answer from the second key separates a key fault from a unit fault, and that single test saves an unnecessary repair on units that were working all along. Note which key gives which result.
When both keys fail in the same way, the unit or its supply is the suspect. When one key works and the other does not, the key list is the place to look and the unit stays closed. Do the test with the keys well apart so the car cannot read both at once.
CAS4 and CAS4+ look alike from the outside and behave the same way in the car, so read the part number from the housing before you plan any work. Both hold the key list and both answer on the bench from a stabilised supply. Save the file before you touch the board.
On the bench the unit is fed at thirteen and a half volts and the current at switch on is noted, because a board that pulls hard has a short on its supply path. Look at the pin row under magnification, since movement at the connector opens solder joints that only show when the car is warm.
The lock is driven from the unit, and it reports back whether it has released, so a lock that does not move leaves the car unable to crank even with a good key. Listen for the click at key on and watch whether the lock bolt actually travels. The noise alone does not prove the lock released.
Measure the lock supply at its connector while the key is turned, because a feed that appears and then falls away tells you the unit is trying and the lock is not answering. If the lock is fed and does not move, the lock is the fault and the unit stays out of the discussion.
Measure the permanent supply and the ignition supply at the CAS connector with the plug fitted, using fine probes through the seal. Both should read at battery level, and a value that sags at key on points at the distribution rather than at the unit. Note the two numbers separately.
Measure the ground at the connector against the battery negative post with the meter on millivolts. A drop that climbs as the car warms leaves the unit working at key on and failing after a short drive, which is the pattern that arrives as an intermittent fault.
A unit that answers on the bench and starts the car with one key only needs the list checked rather than the board repaired. Read the list and compare the entries with the keys you have in front of you, because a key that was never written appears exactly like a key that failed.
After any replacement unit is fitted the coding is written and the keys are tested one by one, with the car locked and unlocked between them. Test the lock release on each key as well, since the lock command comes through the same unit and a list error shows there first.
Record the result of the second key test at the top of the sheet, because it decides everything else. Add the supply and ground values you measured at the connector, then the part number from the housing and the chassis number, so the next reader knows which unit is in the car.
Note whether the fault appears cold or after a drive, and whether the lock clicks without moving. Those two notes describe the failure better than a fault code does, and they are what a bench test is planned from.
Test both keys at the end, with the locks cycled between them, and confirm the steering lock releases each time the key is turned. A car that starts on one key and not the other is not finished. Write the result of each key on the sheet.
Tell the owner that a key which was never written cannot be repaired by a unit repair, because the fault is on the key. Pack the unit in antistatic foam if it travels, and send every key the owner has with it so the list can be checked in one pass.
Record the key data before the first intervention, because the list of keys lives in the module and a careless write erases it. Photograph the part number and the coding index, read the immobiliser status with the second key in the slot, and note which positions the ignition switch reports. Once the vehicle starts with both keys the repair is finished, and any remaining complaint about comfort functions belongs to a different module and a different test.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Opens but does not crank | Steering lock not releasing | Lock supply at its connector at key on |
| One key works, the other does not | Key list entry missing | Result of the second key test and the list |
| Fails after a drive, works cold | Ground drop at the CAS connector | Millivolt drop to the battery negative post |
| Nothing at key on | Supply missing at the unit | Permanent and ignition supplies with the plug fitted |
Because a different answer from the second key separates a key fault from a unit fault in one step. Without that test a working unit can be sent away while the fault sits on the key in the owner pocket.
The work on the board follows the same order, but the part number is read first because the two units are not interchangeable. The file is saved and the supply is measured at the connector in both cases.
Yes, the lock reports back when it releases, and a lock that clicks without moving leaves the car unable to crank. The lock supply is measured at its connector while the key is turned.
The coding is written and every key is tested one by one with the car locked and unlocked between them. The lock release is checked on each key, because the command comes through the same unit.