An Audi with the ABS lamp lit and no other warning alongside it is usually reporting a unit that lost its supply or a pump it cannot drive. The A3 and the A6L share the pattern at the unit connector, while the Q7 adds the V64 pump on its own circuit. Supply is measured first on all three.
The ABS lamp comes on and stays on, sometimes with the traction lamp beside it, and the brakes work normally underneath. That combination tells you the hydraulic part is intact and the unit has lost something it needs, either a supply or a signal from a wheel.
Watch whether the lamp goes out after a restart and returns once the car moves. A lamp that clears at a restart and returns at walking pace points at a wheel signal, while a lamp that stays on from key on points at the unit and its supply. Write down the moment the lamp appears, because it narrows the search more than the code text does.
Read the ABS address and write the entries as the tester prints them, then look at the wheel speeds in the live values while the car rolls. A wheel that reads zero while the others read the same speed names a sensor or its wiring, and the unit is not the suspect.
Clear the codes and repeat the read after a short drive so you see which entry returns first. An entry that returns before the car moves describes a supply or an internal fault, and that difference decides where the meter goes next.
Measure the permanent supply and the ignition supply at the ABS unit connector with the plug fitted, using fine probes through the seal. Both should read at battery level, and any value below that is a drop the unit will report as a fault of its own.
Measure the ground at the same connector against the battery negative post with the meter on millivolts. A drop that climbs when the pump runs leaves the unit working at a standstill and failing under braking, which is a pattern worth chasing before the unit is opened.
A supply that reads well at rest can fall away when the pump draws current, so repeat both measurements while an assistant holds the brake pedal and the pump runs. Watch the meter rather than guessing, because the drop lasts a moment.
Clean the ground point and repeat the reading on the same pins so the change is visible, then write both values down. A unit that was starved under load will behave after the repair, and the sheet should show why.
On the Q7 the ABS unit drives the V64 pump, and a pump that does not run leaves the lamp on with an entry that names the pump circuit. The pump sits on its own mount with a connector exposed to water thrown from the wheel, which is where the fault usually starts.
Open the pump connector and look at the pins before you measure, since green deposit there stops the pump without any fault inside the unit. Check the mount and the earth strap as well, because a pump that is poorly earthed draws more current than the unit expects. A pump that has been wet for a while shows corrosion on the mount as well as in the plug.
Measure the supply at the pump connector while an assistant triggers the pump through the tester, and note whether voltage arrives and stays for the length of the test. Voltage that appears and falls away names a supply path, while no voltage at all names the unit output or the wire.
Then measure the pump motor resistance across its own terminals with the connector off, and compare the value with the data for the part. A motor that reads open is the fault, and a motor that reads correctly moves the search back to the unit and the harness. Compare the reading at the motor with the reading at the pump plug, because a harness fault shows in one and not in the other.
A pump that runs when fed directly rules out the motor and the mount, and it also proves the hydraulics can build pressure. A pump that does not run when fed directly is the fault, whatever the unit stores.
A circuit that carries voltage to the pump and a pump that runs still leaves the unit as the suspect when the lamp returns at once, because the unit may be unable to drive its own output. That is the point where the unit goes on the bench.
Drive the car and brake hard enough to bring the pump in, then read the codes again with the lamp watched from the driver seat. A lamp that stays out through several pump cycles is the result to write on the sheet.
Give the owner the supply and ground values you measured, together with the pump resistance if the Q7 was involved. Tell them whether the fault was in the circuit or in the unit, because that answer decides what is checked if the lamp returns.
Watch the wheel speed signals on a road test with a scope or a live data log, not in the workshop at idle. All four channels must show the same shape at the same time, and the amplitude must stay stable from walking pace to sixty kilometres an hour. If one channel flattens or drops out only on rough tarmac, the cause sits in the bearing or the harness routing, and the pump and the module are both innocent.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Lamp on from key on | Supply missing at the unit | Permanent and ignition supplies at the plug |
| Lamp returns under braking | Ground drop under pump load | Millivolt drop to the battery negative post |
| Entry names the pump on a Q7 | V64 connector or motor | Voltage at the pump plug and motor resistance |
| Lamp clears and returns at walking pace | Wheel signal lost | Wheel speeds in the live values while rolling |
The brakes still work, but the unit is not intervening and the wheels can lock under hard braking. The car is brought in rather than driven for long, and the codes are read before anything else.
Because the pump draws current for a moment and a supply that reads well at rest can fall away during that moment. The measurement is repeated with the pump running so the drop is visible on the meter.
Voltage is measured at the pump plug while the pump is triggered through the tester, then the motor resistance is read across its own terminals. A pump that runs when fed directly clears the motor.
The unit can be unable to drive its own output while everything around it measures correctly. That is the point where the unit goes on the bench for a test under load.