A W221 that accepts the key and then does nothing when it is turned leaves the driver with a dash that stays dark and a starter that never turns. The ignition switch inside the dash switches terminal 15 and passes the start request on, so both sides of that plug are measured before the unit is condemned. The order below separates a switch contact from a car that will not authorise a start.
The owner turns the key and hears nothing, then reports that the steering stays locked and the dash stays black. Some report that the radio comes on and the dash lights up but the starter is silent, which is a different fault and it is written down separately. Ask whether the key is recognised, because a car that does not see the key never gets as far as a crank. Note the number of keys the owner has.
Ask what happened in the days before. A flat battery or a boost from another car sits in front of this complaint on a W221. Write the answer next to the mileage. A switch that lost its supply during a boost is often healthy and the fault is a fuse that was not checked.
Connect the tester and read every address, then look at the ignition switch on its own. Read the key authorisation page and confirm that the car recognises the key that is in the slot. A car that does not authorise the key will never crank, and no measurement at the starter will change that. Hold the key still in the slot while the page is read.
Save the identification page and the coding data, then read the fault memory of the front module that carries the starter relay. A code that names a start request or a selector range tells you where to measure next. Write down the addresses that did not answer, since a dead module on the same circuit changes the whole picture.
Terminal 15 is the ignition feed that the switch closes, and it wakes the dash and the engine unit. Back probe the terminal 15 output at the switch plug with the key turned to the run position, and read it against battery negative. A pin that stays at zero while the key is in run has an open contact or no supply into the switch.
Read the supply pins into the switch at the same time, because a switch with no feed cannot output anything. Load the output with a bulb and read it again, since a contact that shows twelve volts open circuit and falls away under a small load is burnt. That reading separates a worn contact from a wiring fault behind the dash. Read the same pin with the key off as well.
Terminal 50 is the start command, and it is measured at the solenoid with the key held in start and an assistant watching the meter. A reading at battery level while the starter is silent sends you to the starter and its earth. A reading at zero sends you back to the switch and to the selector, and to the relay that carries the command.
Hold the key in start for no more than a few seconds at a time and let the starter cool between attempts. Read the voltage at the solenoid and at the battery post in the same attempt, because the difference between those two numbers is the drop in the cable. A drop above a volt sends you to the cable and its terminals. Write both numbers on the sheet.
The car will not crank unless it knows the selector is in park or neutral, so the range is read on the live page while the lever is moved. A range that does not change, or that shows a gear with the lever in park, stops the start before the switch is involved. Move the lever through every position and watch the value.
On a car with keyless start the brake pedal has to be read as pressed, so the pedal switch is checked next. Read the switch status on the live page with the pedal down, then measure the contacts at the plug. A switch that never closes blocks the crank and it is a common cause of this exact complaint. Read the pedal status twice, once with a light press and once with the pedal on the floor.
Put the meter across the engine block and the body with the key held in start and read the volts. A healthy strap shows a fraction of a volt. A strap that has corroded shows several volts and the starter turns slowly or not at all, even with a good battery and a good command. Look at both ends of the strap before you measure.
Measure from the battery negative post to the body as well, then repeat both readings with the headlights on. A drop that appears with a load belongs to the strap or to the terminal. Clean both ends of the strap and refit them dry, then read again before any unit is removed from the car.
On the bench the switch is powered and each position is selected in turn while the contacts are measured for resistance. A contact that reads more than a fraction of an ohm in the run position has burnt, and it will heat under the load of the dash. Write the value for every position, not only for the one that failed. Read each position twice as well, since a contact that is cooling changes between sweeps.
Watch the current that the switch carries at run, since a contact that is failing shows a voltage drop that grows as it warms. Leave the unit powered for several minutes with the dash load simulated, because a contact that passes a cold test opens when it is hot and the car fails again at the next junction.
Fit the switch and connect the battery, then turn the key through every position before the first start. Watch the dash for the lamps that should come on at run, then crank. A car that cranks and runs but shows no dash lamps has a second fault on the cluster circuit, and that is written on the sheet.
Write the terminal 15 and terminal 50 readings on the sheet, with the selector range and the earth drop. That record is what makes the second visit short when the car returns with a starter that is slow. Check the key authorisation once more before the car leaves, since a switch that was fitted without the key being relearned will not start. Add the key number to the same line on the sheet.
Judge the repair on a cold morning with the battery at rest, since a switch that is marginal passes a warm test. Read the battery voltage before the first crank and again while the starter turns, and write both numbers down. A battery that falls below ten volts under the starter makes every other reading worthless, and it is checked before any unit is removed. Put the charger on overnight.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Dash dark at run, no crank | Terminal 15 contact open | Terminal 15 output at the switch under a bulb |
| Dash alive, starter silent | No command at terminal 50 | Solenoid voltage with the key held in start |
| Crank refused with the lever in park | Selector range or brake switch | Range and pedal status on the live page |
| Slow crank with a good battery | Earth strap or cable drop | Volts across the strap while cranking |
An automatic W221 cannot be push started, and the selector will not leave park with the engine off. The start command is measured at the solenoid before anything else is tried.
Terminal 15 is not closing, so the dash and the engine unit never wake. The output at the switch is read under a load, because an open circuit can still show twelve volts.
It is possible, and it is proven with a meter at the solenoid. Battery level there with a silent starter sends you to the starter, while zero sends you back to the switch and the selector.
The key authorisation is checked after the fit, and the car is read again on the tester. The readings from before the repair are kept so the new unit is judged on the same numbers.