PGE Tuning Lab

BMW RDC tyre pressure warning that will not clear

The warning comes on, so the driver checks the pressures at a filling station and finds them even. The system is reset and the warning returns within a few days with the tyres still correct. On the E90 and the F25 the RDC unit reads a sensor in each wheel, and one of those sensors has stopped reporting the pressure it measures.

What the warning does

The warning may come on after a long drive, or it may stay on from the moment the car is started and never clear at all. The driver has usually had the pressures checked and found them even on all four wheels. Ask whether the warning returns at the same point on the same trip, since a warning that repeats at one place in the route is a wheel that loses its signal there. A warning that comes on after the car has stood for a week is a different fault from one that comes on at speed.

Ask whether the wheels have been changed, swapped front to rear, or had new tyres fitted recently. A sensor that was not learned after a wheel swap gives a warning that no reset will clear, and the driver will have paid for a reset already. Write those answers down with the pressures the driver saw on the gauge, because a real pressure loss has to be ruled out before the electronics are blamed for anything.

Which system the car has

The E90 was built with two different systems over its life, and the early cars read the pressures through the wheel speed sensors of the stability control. The later cars and the F25 use a sensor inside each wheel that transmits its own pressure and its own temperature. Look at the valve stem, since a metal stem held by a nut belongs to a sensor and a plain rubber stem does not.

The two systems are diagnosed in different places, so confirm which one is fitted before you open anything at all. A car with wheel sensors appears in the tyre pressure address of the tester, and a car without them has nothing in that address. Getting this wrong sends you looking for a unit the car never had.

Reading the unit

Open the tyre pressure address and read the fault memory before you reset anything, since a reset in the unit takes the evidence with it. Entries that name a wheel position as not received are the ones that matter here, and the position in the entry is the wheel to look at first. Write the entry down with its frequency, because one that returns after a clear is current and one that does not is history.

Read the learned sensor identities and compare them with the sensors now fitted to the wheels. A learned list that names an identity no wheel answers means a wheel has been swapped without a learn, which is the most common cause on a car that has just had tyres. That fault is cured by the learn procedure and by nothing else, and no amount of driving will settle it.

Testing the sensors

Use a trigger tool at each wheel in turn and read the pressure the sensor reports and the identity it sends back. A sensor that answers gives you a figure you can compare with a gauge on the same valve. A sensor that stays silent has a flat battery inside it or has been damaged by a tyre fitter who levered against it. Work round all four wheels even after you have found one that is silent.

Compare the identity the tool reads with the identity stored in the unit for that position. A sensor that answers with an identity the unit does not know has never been learned, and the learn is the repair. A sensor that answers with the right identity and a plausible pressure has done its job, and the fault moves to the antenna behind it.

The learn procedure

The learn is started from the tester with the car standing still and all four sensors awake, and the unit stores the identity it hears at each position. A learn that completes leaves a list you can compare with the wheels on the car. Drive the car above the speed the unit asks for afterwards, since the unit confirms that list while the wheels turn. A learn that never confirms leaves the warning on and the list unchanged.

A learn that refuses to complete usually has one sensor that never answers, and the trigger tool finds that sensor in a minute. Write the new list on the sheet, because the next visit should not start from a blank page. A car that loses its list after a week has a supply fault that resets the unit, and the ground is measured before any sensor is blamed again.

The antenna and the receiver

The RDC unit listens through an antenna near each wheel arch on these cars, and one antenna that has failed leaves one corner deaf to every sensor fitted there. Move the trigger tool to a wheel that is known to work and see whether the tool still reads there, then move back to the dead corner. A tool that works at three wheels and not at the fourth has found the corner itself.

Swap the antenna with one from another position where the wiring reaches, and see whether the dead corner moves with the antenna or stays where it was. That test takes minutes and it separates the antenna from the unit without a part being ordered.

Supply and ground

Measure the supply at the RDC unit connector with the plug fitted and fine probes through the seal, and measure the ground pin against the battery post on the millivolt range. A unit that resets on a poor ground loses its learned list and then reports the same wheel on every cold start. Clean the stud, repeat the reading and read the learned list again before the unit is condemned for anything. A drop above fifty millivolts is enough to cause this.

Measure the battery under load as well, since a car with a weak battery can drop the supply to the unit during a cold start and the unit then forgets what it learned. Check the fuse contact across its blades while the unit is awake, because a fuse that has gone warm shows a drop that a meter on the battery side never reveals. A supply fault in this circuit looks exactly like a sensor fault on the road.

What confirms the fault

The fault is confirmed when the pressures are right on a gauge, one sensor fails to answer the trigger tool, or one sensor answers with an identity the unit has never learned. Each of those results names a single wheel and a single repair, and none of them needs the other three wheels disturbed.

Write the identities and the trigger results on the sheet, with the gauge pressures beside them, because the next visit starts from that record and a second sensor will fail in time. Learn the sensors, drive the car above the speed the unit needs for a few minutes, and read the unit again afterwards. A warning that returns with a correct learned list sends you back to the antenna and to its plug.

Check the pressures with a gauge before anything electronic, then trigger each sensor and read what it sends back. Compare those identities with the learned list in the unit, position by position. A silent sensor or an unknown identity names the wheel, and an antenna swap settles the rest of the job.

What is measured when the RDC warning will not clear
SymptomLikely causeWhat is measured
Warning returns after every resetSensor not learnedLearned identities against the sensors in the wheels
One wheel never reportsSensor battery flatTrigger tool at each wheel, pressure and identity
Warning appears at one place on a routeAntenna blind spotTrigger test repeated at a known good wheel
Same wheel reported every cold startSupply or ground at the unitFeed at the plug, ground drop on the millivolt range

Frequently Asked Questions

Can the warning be turned off for good?

The unit reports what the sensors send, so a sensor that is silent keeps the warning on. A learn with a correct sensor set is what clears it.

How long does a wheel sensor last?

The battery inside is sealed and ages with use, so an old sensor goes silent without warning. A car with one silent sensor usually has others close behind it.

Does a wheel swap need a learn?

The unit stores an identity for each position, so a wheel moved to another corner answers with an identity the unit does not expect. The learn is run after any swap.

What is checked after the repair?

The learn is completed, the car is driven above the speed the unit needs, and the entries are read again. A warning that returns means a second sensor or an antenna is still at fault.

Related Services