PGE Tuning Lab

VW Golf 6 steering column lock that will not release

The driver puts the key in, turns it, and nothing happens at all. The dash tells the driver that the steering lock is defective, and the car may or may not crank on the next attempt. A refusal in a car park with the wheel turned hard against the stop is the usual way this arrives. The lock is an electric unit on this platform, and the checks below decide whether it is the unit, the supply or the key.

What the driver reports

The key goes into the barrel and refuses to turn, or it turns and the dash shows a message about the steering lock with the ignition staying off. Sometimes the car starts after the wheel is rocked, which teaches the driver a habit and hides the fault for a while. Ask whether the wheel was rocked and whether the message appears every time or only when cold. A car that has stood for weeks belongs in the same question, since a lock left engaged for a long time can stick in its bore.

Ask whether the car has recently had a flat battery or a jump start, since a lock that was left half way through its cycle can stay there until it is driven again. Ask too whether both keys behave the same way. A fault that follows one key is a key or reader problem, and the second key settles it in a minute. Write both answers on the sheet before you touch the column.

The unit and what it does

The column lock is a motor driven bolt that holds the column while the car is parked, and the unit reports its position to the immobiliser before it allows the ignition. When the bolt does not retract, the ignition stays off and the driver feels a key that will not turn. On these cars the unit talks to the immobiliser over the comfort network and it needs that link alive to move at all. The unit sits on the column under the shrouds.

The bolt is driven by a small motor with a worm gear, and the position is read by a switch inside the unit. A motor that has worn its brushes and a switch that has stopped reporting look the same from the driver seat and are separated by the tests below. The unit also carries the key reader on some builds, so the part number matters when a replacement is ordered.

Reading the unit before anything

Open the column lock address in the diagnostic session and read the fault memory before the key is cycled any further. Entries about the lock motor and about the position switch are the ones that matter, and an entry about the immobiliser refusing the start belongs with them. Write each entry down with its frequency, because an entry that returns after a clear is current.

Read the live values for the lock position while the key is turned and watch whether the value changes at all. A value that stays at locked while the motor is heard to run says the switch has stopped reporting. Listen with the door open and the workshop quiet, because the motor is small and a busy bay hides it completely. A value that stays at locked with no sound from the column sends you to the motor and to its supply.

Supply and ground at the unit

Measure the permanent feed at the unit connector with the plug fitted and fine probes through the seal, and measure the ignition feed in the same way. Both should sit at battery level and the permanent feed must hold while the starter turns. A feed that sags when the starter loads the battery leaves the unit unable to finish its cycle. Measure across the fuse that feeds the unit as well, since a contact that is warm shows a drop between its blades.

Measure the ground pin against the battery post on the millivolt range, and do it while the motor is being commanded so the circuit is loaded. A drop above fifty millivolts makes the motor weak and the bolt slow, and the driver feels a key that turns a little and stops. Clean the stud and repeat the reading before the unit is condemned.

The motor and the bolt

Take the shrouds off and listen at the column while an assistant turns the key. A motor that runs and a bolt that does not move means the gear has stripped or the bolt is jammed in its bore. A motor that is silent means no command or no supply, and the connector is measured next.

Measure the motor feed at the unit plug during the command with a scope, since a short pulse that a meter never catches is enough to drive the bolt. A pulse that is present with a silent motor means the motor winding is open, and the unit is opened on the bench. Write the pulse length down, because a pulse far shorter than the one on a healthy car tells you the unit is shutting down early.

The key and the reader

Try the second key with the first one well away from the barrel, because two keys read at once give a car that reports a key present and then declines to start. A fault that moves with the key is a key problem. A fault that stays with the car is the reader or the unit.

Read the immobiliser values and confirm that the key is accepted while the lock is still reported as engaged. A key that the car accepts and a lock that will not release is a unit fault, and the two readings together are the evidence. Write both values on the sheet before anything is replaced.

The mechanical side

Check the column for a lock that is jammed by the wheel being forced against the stop, since a driver who has fought the wheel can wedge the bolt. A wheel pulled hard against that stop puts a load on the bolt that the small motor cannot overcome. Straighten the wheel and try again with the load off the column. A lock that releases with the wheel free is a mechanical complaint that needs the driver spoken to.

Look at the ignition barrel itself where the key will not turn at all and the message is absent. A barrel with a worn tumbler gives a key that sticks and a column that never gets a command. That fault is mechanical and the electrical checks above will all pass, which is what tells the two apart.

What confirms the unit

The unit is the fault when the feeds and grounds hold under load, the command pulse reaches the motor, the bolt does not move and the position value never changes. Those results together leave the motor and the switch inside the case, and the unit goes on the bench.

Write the position values and the pulse readings on the sheet before the unit leaves the car. A replacement needs its own coding before the immobiliser accepts it, so the old values are read first. Cycle the key three times and rock the wheel between attempts before the car goes back. Then leave it locked overnight and try it again from cold.

Read the live position value while the key is turned, because a value that never changes has taken you past the motor and the supply. Then measure the permanent feed under load and the ground on the millivolt range. A command pulse at a silent motor with a healthy supply is the unit, and the bench work is quick once the case is open.

What is measured on a Golf 6 whose key will not turn
SymptomLikely causeWhat is measured
Key will not turn, message on the dashBolt not retractingLive position value while the key is turned
Motor silent, no messageCommand or supply missingScope on the motor feed during the command
Motor runs, bolt stays outStripped gear or jammed boltSound at the column, current draw of the motor
Fault follows one key onlyKey or readerSecond key tried with the first well away

Frequently Asked Questions

Can the car be started with the lock engaged?

The immobiliser allows the start only when the unit reports the bolt retracted, so the engine stays off while the value says locked. The position value is the first thing read.

Does a flat battery cause this?

A supply that falls during the lock cycle leaves the bolt part way and the unit confused about its position. The battery is measured under load and the unit is cycled again afterwards.

Is a used unit a straight swap?

The unit carries data the immobiliser checks, so a used one is coded before the car will start. The values from the old unit are read and written down first.

What is checked after the repair?

The key is cycled three times with the wheel rocked between attempts, then the car is left locked overnight and tried again from cold in the morning.

Related Services