An E90 that lights the DSC lamp and the yellow brake lamp together has usually lost a trustworthy steering angle, and the car switches those systems off to protect itself. The sensor sits in the column behind the wheel and it reports two signal tracks that the car compares against each other. The order below tells you whether the angle the car receives is wrong, and whether the column cluster is the part at fault.
The driver reports two lamps that stay on after a start, a message about driving stability on the screen, and cruise control that no longer holds a speed. Some report a heavy steering feel at low speed, which follows the loss of the stability function rather than a fault in the rack. Ask whether the lamps came on after an alignment or after work on the front suspension.
Ask whether the lamps reset after a restart and come back after a few hundred metres of driving. A lamp that clears at a key cycle and returns once the car moves is a plausibility fault, and it is settled with the angle value. Write the answer on the sheet with the mileage, since the history decides whether you start with a calibration or with a measurement. Add the tyre sizes as well, because mixed sizes read as an angle that never settles.
Read every address, then open the stability unit and the column cluster on their own and write the exact code text. A code that names the angle sensor and a code that names a plausibility check between the angle and the yaw rate send you to different measurements. Save the freeze frame before clearing anything.
Write down the battery voltage from the freeze frame as well. An E90 that cranks on a weak battery writes angle codes that mean nothing, and the car behaves correctly once the battery is charged. Check the charging voltage at idle before any part is condemned, because a low supply gives a fault that returns the day after a repair. Read the battery at rest first as well, since a surface charge on its own proves very little.
With the tester on the live page, read the steering angle with the wheels straight and the engine running. The figure should sit close to zero, and a few degrees of offset is normal after an alignment. Turn the wheel slowly to full lock on each side and watch the value move without a jump. Read the value with the engine off as well, since a supply that is clean only while the alternator runs hides a fault.
A value that stays at one number while the wheel turns is a sensor that has stopped reporting. A value that jumps in steps points at a dirty or worn track inside the sensor. Write the figure at centre and at each lock, then at a quarter turn, because those four numbers show a sensor that is dropping part of its travel.
The sensor runs on a regulated supply, and it needs a clean ground to report an angle. Measure the supply pin at the plug with the ignition on and compare it with the figure the tester shows for the same circuit. A supply that is low puts the angle out of range and the car switches the systems off.
Put the meter on millivolts and read from the ground pin to the battery negative post while the wheel is turned. A drop that moves with the wheel is a poor ground inside the column, and it gives an angle that wanders. Wiggle the harness at the column while the value is on screen, since a broken strand in that loom copies a failed sensor. Read the same drop with the engine running and the lights on, then compare the two figures.
The sensor reports two tracks that move in opposite directions, and the car checks that their sum stays constant across the travel. Measure both signal pins at the plug while an assistant turns the wheel slowly from lock to lock, and write the two voltages at each quarter turn.
Add the two figures at each point. A sum that holds steady while the wheel turns means the sensor is reporting honestly and the fault sits in the calibration or in the car. A sum that drifts names the sensor or its optical disc, and no amount of calibration will fix it. That sum is the single most useful number on this job, so write it on the same line as the two voltages.
If the angle reads correctly and the sum holds, the fault is often an offset written into the car after an alignment or a suspension repair. Read the stored offset and compare it with the angle at centre. Write the offset on the same line as the angle, because the two are only useful together. A stored offset that does not match the wheels straight ahead makes the car distrust the sensor within a few hundred metres.
Run the calibration by the book with the wheels on a level surface and the steering centred by a proper gauge. Then drive the car and read the angle again at centre. A value that moves away from zero after a drive is a mechanical fault in the column, and it is settled before any calibration is repeated.
On the bench the column cluster is powered and the angle is read while the shaft is turned by hand through its travel. A cluster that reports smoothly through the range is healthy and the fault is in the car. One that drops its signal at a point in the travel has a failed sensor inside it.
Feed the unit at thirteen and a half volts and watch the current it draws while the angle is swept. A unit that draws more than its neighbours among the same part number is running hot, and it will fail again in the car. Keep it powered for several minutes, since these sensors drift with temperature and a cold test hides it.
Fit the column parts and connect the battery, then turn the wheel lock to lock twice before a calibration is attempted. Then read the angle at centre and confirm that both tracks are clean. A car that reads zero at centre and still lights the lamps has a second fault in the stability unit, and that is read next.
Write the angle at centre on the sheet with the two track voltages and their sum, then add the calibration result. That page is what makes the second visit short, and it also shows whether the column moved after a kerb strike. Check the tyre pressures and the ride height before the car leaves, since a car that sits uneven reads an angle that is never right.
Judge the repair on a straight road at speed rather than in the workshop. Read the angle at centre before the drive and again afterwards, and note whether the two numbers agree. A car whose angle drifts after a drive has a column that is moving or a track that is failing, and the lamps will return on the next long trip. Note the time of the drive on the same sheet.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Lamps after an alignment | Offset written into the car | Angle at centre against the stored offset |
| Value frozen while turning | Sensor not reporting | Angle on the live page through the full travel |
| Value jumps in steps | Worn track or dirty disc | Both track voltages, and their sum at each point |
| Lamps return after a drive | Poor ground in the column | Millivolt drop at the ground pin while turning |
It drives, but the stability function is off and there is no cruise control. The angle value is read first, since a car with a correct value needs a calibration rather than a part.
It does, with the wheels straight on level ground. The angle at centre is read before and after so that an offset is not mistaken for a fault.
The car drops the stability function and the parking brake assist when it cannot trust the angle. One bad signal switches both systems off, and the code text names which one it distrusted.
The stability unit and the yaw rate signal are read next. A sensor that reports correctly still gives a plausibility code if the car compares it against a signal that is wrong.