PGE Tuning Lab

VW Passat B6 seat heating with one seat that stays cold

The switch lights up, the driver waits, and the seat stays cold while the other one works as it always has. On the Passat B6 each seat has its own heating element in the cushion and another in the backrest, and one of them has failed. The order below finds which part of the seat circuit has gone and leaves the climate panel alone until it is proven.

How the fault looks

The seat stays cold from the first minute, or it warms for a while and then goes cold again, which tells you the element is broken and touching as the seat moves. Ask whether the backrest heats and the cushion does not, since the two are separate elements on a shared connector. That answer saves the whole measurement on some cars and points straight at one half of the seat.

Ask whether the passenger seat has been used with a heavy load or with a child seat fitted for years, because a cushion that has been pressed hard has usually failed at the bolster. Ask too whether the fault came after the battery was changed, since a climate unit that lost its coding will not switch a heater on at all. Write both answers on the sheet before the meter comes out of the box.

How the seat is wired

The cushion and the backrest each have their own element, and both are fed through a connector under the seat that also carries the sensor wires. A temperature sensor sits in the cushion and tells the control unit how warm the seat has become. The unit under the seat switches the current, and the climate panel only sends the request through the bus.

That arrangement means a dead seat can be a request that never arrives, a unit that will not switch, a broken element or a sensor that reads wrong. Each of those leaves a different trace on the tester, which is why the readings below come before any part is ordered. The connector under the seat is where most of them are made, and it is reached by lifting the seat or by sliding it fully forward.

Reading the request

Open the climate unit and read the seat heating request while an assistant works the switch through its settings. A request that rises with each press proves the panel and the wiring up to the unit. A request that stays at zero sends you to the switch and to the panel, and the seat is not the subject at all. Write the request figure for each setting on the sheet.

Read the seat temperature value in the same session and compare the two seats at the same moment with both switched off. A cold seat that reports a high temperature has a sensor that has failed, and the unit refuses to heat a seat it believes is already hot. That fault is common and it is spotted on the tester before a cover comes off.

Measuring the element

Unplug the connector under the seat and measure the resistance of the cushion element and of the backrest element with the meter on its lowest range. A good element reads a few ohms and an open one reads nothing at all. Write both figures on the sheet, because the pair tells you which half of the seat has gone and whether the other half is close behind.

Wiggle the harness at the flex point while the meter is connected and watch the reading on the screen. A figure that jumps as the seat is moved has a broken wire that touches when the seat is in one position. That fault heats the seat on the way to the workshop and goes cold on the way home, which is why the driver is never believed. Move the seat through its full travel while the meter is watched.

Voltage and current

Plug the connector back in, switch the heating on and measure the voltage at the element with the plug fitted and fine probes through the seal. Battery voltage at the element with a cold seat means the unit is switching and the element is open. No voltage means the unit has decided not to switch, and the request and the sensor value are read again. Those two readings together settle which end of the circuit has failed.

Clamp the feed wire and read the current while the seat heats from cold, then watch it as the seat warms over a few minutes. A current that is present and falls as the seat warms has a working circuit and a sensor that is reading the temperature. A current of zero with voltage present means one of the two readings is wrong and is repeated with a second meter.

The unit under the seat

Read the entries in the climate unit before you clear them, since an entry about an open circuit on one seat names the circuit and the side of the car. Measure the feed and the ground at the unit under the seat with the plug fitted and the heater switched on. A ground that has corroded under a seat that has seen spilled coffee is a common find on a car of this age. Clean the stud and read the current again before the unit is replaced.

Check the fuse that feeds the seat heating and measure across its blades while the heater is on. A fuse contact that has gone warm shows a drop that a meter on the battery side never reveals. A seat that works when the fuse is wiggled has a fuse box problem that will come back within weeks.

The harness and the flex point

Look at the loom where it leaves the seat frame and runs down to the floor, because that is where it bends every time the seat moves. A wire broken inside its insulation looks perfect and reads open when the seat is forward, which is why the reading is taken in both positions. Pull the boot back and look at the strands under a lamp. A strand that has gone green has been damp and will break next.

Check the connector under the seat for a pin that has been pushed back, since a seat that has been moved over a vacuum cleaner hose often has one. Push each pin home and repeat the resistance reading with the plug fitted. A reading that changes when the plug is pressed has found the fault without a part being ordered.

What confirms the element

The element is the fault when the request arrives, the unit switches voltage to the plug and the resistance reads open on one half of the seat. Those results together name the cushion or the backrest, and the cover comes off once.

Write the request and the resistance on the sheet, with the sensor value beside them, because a seat that comes back cold needs that record. Test the heater through a full warm up after the repair and watch the current fall as the sensor takes over. Then sit in the seat and move it through its travel while it heats, since a joint that fails under load shows up in that minute.

Read the request and the seat temperature value first, because a sensor that lies keeps the unit from switching at all. Then measure the resistance of both elements at the plug under the seat, and wiggle the harness while the meter is connected. An open element with voltage at the plug ends the job.

What is measured on a Passat B6 with one cold seat
SymptomLikely causeWhat is measured
Switch lights, seat stays coldOpen elementResistance of cushion and backrest at the plug
Cold seat reports hotSensor in the cushionSeat temperature value against the other seat
Heats in one position onlyBroken wire at the flex pointResistance while the seat is moved
Nothing at the element plugUnit under the seat or its feedVoltage at the element with the plug fitted

Frequently Asked Questions

Can the element be repaired without removing the cover?

A break at the bolster is reached by lifting the cover at the edge and joining the wire with a crimp. A break inside the cushion needs the cover off.

Why does the seat go cold after a few minutes?

The element opens as it expands, or the sensor reads high and the unit backs the current off. Both are separated by the resistance reading and by the temperature value.

Does the climate panel need coding after a battery change?

The panel keeps the seat settings, and a unit that has lost its coding will not switch a heater on. The coding is read before the battery is disconnected.

What is checked after the repair?

The seat is run through a full warm up with the current watched, then the seat is moved through its travel while it heats. A current that falls as it should means the sensor is working.

Related Services