Tail lights that go out together with the central locking on a W204 point at the rear SAM in the boot, because that unit drives both the lamps and the lock motors. Water in the boot well is the usual reason for it. The supplies and the ground are measured before the unit is opened.
The tail lights go out and the central locking stops answering on the same day, while the car still starts and drives. Owners usually report one of the two, so ask about the other, because one unit in the boot drives both functions. A single fault that takes two functions away is easier to place than two faults that seem to have arrived together. The lamps and the locks sit in the same group of outputs, so a lamp that stays dead while the lock still works already tells you the fault is on one output.
Ask whether the boot has been wet, whether anything was spilled in it and whether the car was parked under trees for a long time. A drain that has blocked fills the well under the unit, and the faults follow a few weeks later. Note which lamps are out and whether both sides are affected.
Read the rear body address and write the entries as the tester prints them. A unit that answers gives you a fault memory and live values for the lamps, while a unit that stays silent sends you to the fuses and the supplies first. Write down whether the address opens at all, because that result decides the order of the tests.
An entry that names an output describes a driver that has shut itself down, and an entry about the interior bus describes a communication fault that may come from another unit on the car. Clear the memory and see what returns with the lamps switched on and with the car locked once and unlocked once.
Measure the permanent feeds at the unit connector with the ignition off and the battery negative post as your reference. Then measure the ignition feed with the key on. Each should read battery level, and a feed that sags points at the rear fuse box beside the unit rather than at the unit itself.
Load the feed with a bulb and read it again, because a corroded terminal holds its voltage until current flows through it. Measure the ground pins against the battery post on the millivolt range with the plug fitted. A drop above about fifty millivolts is enough to make the lamps dim and the locks sluggish on a cold morning. The rear fuse box sits beside the unit and takes the same water, so its terminals are cleaned in the same pass.
Lift the boot floor and look at the well around the unit for water marks and for a tide line on the carpet. Look at the connector for green deposit on the pins, then at the board through the slot for a white bloom. Water damage explains faults that move from one output to another over a few weeks. Silt on the carpet and a bloom on the board are the same story seen at two different stages of the leak.
Clean the pins and repeat the same measurements so the change is visible in your notes. If the same lamps fail after cleaning, the damage is inside the housing and the repair is on the board. If different lamps fail, the leak is still active and the seal or the drain is repaired before the unit is worked on.
Back probe the tail lamp output at the unit connector with a bulb fitted in place of the lamp. A pin that shows twelve volts with no load and drops to a few volts with the bulb connected is a driver that has failed inside the unit. The loom plays no part in that reading, which is why it is worth more than a check along the wire.
Repeat the test on the pin for the other side, since this unit drives left and right from separate outputs. One side that holds its voltage while the other collapses narrows the fault to a single driver. Check the lamp holders as well, because a corroded holder pulls more current than the driver expects. Fit a new holder and repeat the bulb test on the same pin, since a cleaned holder can still read high once it warms up.
The unit feeds the lock motors in the rear doors and in the boot, so a dead output there stops the central locking while the remote still works at the front doors. Measure at the motor plug while an assistant presses the button and note whether voltage arrives at all during the press.
Voltage that arrives and no movement puts the fault on the motor, and the unit is cleared of that complaint. No voltage at the plug during a press sends you back to the unit output, and that output is then measured with a bulb in place of the motor to see whether it holds under load.
The unit talks to the rest of the car on the interior bus, and a bus fault takes the lamps and the locks away at the same moment. Measure the two bus wires at the unit connector with the ignition on and the meter on direct current. Each should sit near two and a half volts, and their sum should stay close to five.
A wire that sits at battery voltage or at zero describes a short on that line, and the bus is split at the unit to find which side holds it down. Unplug the unit and measure the bus again on the car side. Values that come back to normal with the unit off put the fault inside the unit.
The fault is inside the rear SAM when the supplies hold under load, the ground drop is low, the bus voltages are correct with the unit unplugged, and an output collapses with a bulb on it. Those results together leave the unit as the repair, and each one is written on the sheet as it is taken. A unit that answers but drives nothing on any output has lost its coding, which is read before the board is opened.
On the bench the unit is fed at thirteen volts and every output is loaded in turn while the current is watched. An output that gives no current with a load attached confirms the internal fault. A unit that drives every output on the bench sends you back to the lamp holders and to the wiring in the boot.
Take the boot trim out before you test anything, because a unit that sits in a puddle reads correctly on a dry day and fails again after the first rain. Lift the carpet and look at the well for a tide line, then at the connector for green deposit on the pins. Write down what you find before it is cleaned. A unit that comes back to life after the pins are dried has water damage that will return unless the leak is repaired as well.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Tail lights and locking dead together | Output group failed in the unit | Output voltage with a bulb on the lamp pin |
| Locks slow at the rear only | Ground drop at the unit | Millivolts from ground pin to battery post |
| Faults move between lamps | Water in the boot well | Pin condition and tide line under the unit |
| No answer from the rear address | Feed or bus fault | Feeds under load and bus volts with the unit off |
One unit in the boot drives both, so a unit that has lost an output group takes both functions away at once. The other complaint is worth asking about even when only one of them is reported.
It answers on the tester and it needs the coding written for the car, then each output is tested in turn. Cars differ in equipment, so the coding is part of the job rather than an optional step.
A fuse that feeds the unit takes every function away at the same moment, so it is measured under load with a bulb on the circuit. A fuse that holds its voltage with current flowing is not the fault.
The supply values, the ground drop, the bus voltages with the unit unplugged and the output voltage at the failed lamp with a bulb connected. Those four numbers describe the fault better than a code entry does.