PGE Tuning Lab

Mercedes W203 front SAM with lights and wipers that come and go

On the W203 the front SAM sits in the fuse box under the bonnet and it feeds the exterior lights along with the wipers and the horn. When it starts to fail, the customer reports lights that work on Monday and not on Tuesday, and the wipers that park wherever they like. The order below works from the water that gets in down to the output stage itself.

How the fault is reported

The customer rarely arrives with one clean symptom. Headlamps that dim when the wipers run and a wiper that stops halfway and starts again after a bump describe the same module from different angles. A horn that works only with the wheel turned belongs with them. Ask which circuit fails first, since the first one to go is usually the one with the heaviest load on it. A lamp that lights only after a bump is a contact problem, and the test below separates the holder from the module.

Ask whether the fault appeared after rain or after the car was washed, because that answer points straight at the fuse box and shortens the job. Ask as well whether a lamp has been changed recently, since a lamp holder pushed in badly can disturb a whole circuit and look like a module fault. Write both answers on the sheet.

Where the module sits and what it feeds

The front SAM is the board inside the engine compartment fuse box, and every exterior lamp output passes through it. It also reads the stalk positions and drives the washer pump, so a fault inside it can show in circuits that look unrelated on the diagram. Open the cover with the battery disconnected and look at the board before you test anything electrical.

Look for a dark patch around a relay or a driver chip. Look as well for a smell of hot plastic and for the white bloom that water leaves on a board. A board with bloom on it has been wet and the fault will keep coming back until the water path is closed. A relay that has run hot leaves its case discoloured, and that colour is easier to see than the fault itself. Photograph what you find before anything is cleaned.

Water and the fuse box

Water reaches this box through a blocked drain below the windscreen and through a cover that has been seated badly after a fuse was changed. Check the drain with a bottle of water and watch where it goes. Check the cover seal for a pinch and the lid for a missing clip, because a lid that lifts at speed lets water in while the car is driven.

Pull every connector in the box and look at the pins under a lamp. A green pin has been wet and the contact is already poor, and a pin that is black has been hot. Clean a green pin only to prove the circuit, because a pin that has corroded once will corrode again. Replace the pin with a new terminal where the crimp tool reaches it, and fit a sealed joint.

Feeds, grounds and fuse contacts

Measure the permanent feed at the SAM connector with the plug fitted and fine probes through the seal, and measure the ignition feed in the same way with the key on. Both should sit at battery level and neither should move when the wipers are switched on. A feed that drops when a load comes on points at the fuse contact or at the supply stud.

Measure each ground point on the inner wing against the battery post on the millivolt range, and do it with the headlamps on so the circuit is loaded. A drop above fifty millivolts is enough to make a lamp dim and a wiper slow. Then measure across the fuses themselves, since a fuse with a poor contact shows a voltage across its blades while current flows.

Reading the inputs on the tester

Open the front SAM in the diagnostic session and read the actual values for the stalk and the switch inputs while you work them by hand. A value that follows the stalk proves the switch and the wiring up to the module, and it leaves the output side as the subject. A value that never changes sends you to the switch and to its plug.

Read the fault memory before you clear it, because entries about a lamp circuit and about a supply voltage tell you which end of the module has failed. Write the entries down with the mileage. A module that reports an open circuit on one output and nothing else is usually repairable, and a module that reports several unrelated outputs at once has a supply problem behind it.

Testing the output under load

Pull the lamp plug and fit a bulb you know works, then measure the voltage at the plug with the circuit switched on. A meter on an open circuit reads battery voltage and tells you nothing, which is why the bulb goes in first. A plug that holds battery voltage with the bulb lit has a healthy output.

Clamp the feed wire at the module and read the current with the circuit on. A current that is far above the lamp rating means a short in the wire or a wrong bulb, and a current of zero with a good bulb means the output stage is open. Compare that circuit against its pair on the other side of the car.

The interior CAN

Scope the two interior CAN wires at the SAM connector with the ignition on and look at the levels and at the shape of the frames. A wire that sits at a fixed level has lost its pair, and the module then reports faults across the whole car. Check the twisted pair for a rub where the loom passes the bulkhead. Sleep and wake behaviour belongs here too, because a module that stays awake drains the battery and reports nothing at all.

Measure the resistance between the two CAN wires with the battery disconnected. A reading far from the expected value points at a broken wire or at a module holding the bus down. Unplug the modules one at a time and watch the reading, since the one that brings the value back is the one at fault.

What confirms the module

The front SAM is the fault when the feeds hold under load, the grounds read low, the inputs follow the stalks on the tester and an output stays dead with a good bulb and a healthy current path. Those results together leave the output stage and the board is repaired or replaced with one coded to the car.

Write every reading on the sheet before the module leaves the car, because a replacement that behaves the same way is a wiring fault you have missed. Cycle the ignition twice and work every circuit once the module is back. Check the fuse box for water again after the first rain, since a repair that lets the water back in will be back in the workshop.

Read the inputs on the tester first, because a stalk value that follows the switch removes half the car from the job. Then measure the feeds with the plug fitted and the grounds on the millivolt range under load. A dead output with a good bulb and a healthy supply is the module, and the water path is closed before the new one goes in.

What is measured on a W203 with intermittent lights and wipers
SymptomLikely causeWhat is measured
Lamps dim when the wipers runGround point or a feedMillivolt drop at the inner wing points under load
One output dead, others fineOutput stage in the moduleVoltage at the lamp plug with a known good bulb
Faults after rain or a washWater in the fuse boxBoard inspection, drain test, connector pins under a lamp
Whole car reports faults at onceInterior CAN held downScope of both CAN wires, resistance with the battery off

Frequently Asked Questions

Can the front SAM be repaired?

A board with a failed output stage is repaired on the bench when the damage is confined to the driver and the supply side is sound. A board with water damage across several layers is replaced.

Why do the wipers stop in the middle?

The park position is held by a contact inside the motor and read by the module, so a lost signal leaves the motor stopped where the switch opened. The motor contact is checked before the module.

Does a replacement need coding?

The module carries the coding for the lamps fitted to that car, so a used one is coded before the circuits behave. The old coding is read and written down first.

What is checked after the repair?

Every lamp circuit is worked once, the wipers are run through all speeds, and the fuse box is checked for water after the first rain. A fault that returns with water means the drain is still blocked.

Related Services