PGE Tuning Lab

BMW E60 parking sensors silent with the PDC module in the boot

An E60 whose parking sensors have gone silent usually has one sensor down, and the module in the boot reports which one it is before you touch a bumper. The system measures distance with ultrasound and turns it into a rate of beeps, so a single failed sensor can leave the driver with nothing at all. The checks below take you from the memory to the click test.

What the driver reports

The button lights up and nothing else happens, or the system beeps once when reverse is selected and then goes quiet. Some drivers report a continuous tone when a wall is still a metre away, and others say the beeps stop halfway through a manoeuvre. Ask whether the fault followed a bump in a car park or a repaint of the bumper, since both change what you find behind the trim.

Ask whether the car has been through a car wash with a high pressure lance close to the bumpers, since water reaches the sensor plugs through the seals. Write down whether the fault is at the front, at the rear or at both ends, because a fault at both ends points at the module rather than at a sensor. Note the build date so the right wiring diagram is used.

Silence and the module behind the trim

The module sits in the boot behind the side trim on this car, and it is the part that drives all the sensors in turn. Pull the trim back and look at the plug for water marks, since the boot of an E60 collects water from a blocked drain and the module sits low in that corner. A plug with green pins explains a system that fails in the rain and works when dry.

Check the module is bolted down and that its earth strap is clean, since the unit uses the body as its reference. A module that has been left loose after a repair gives readings that change with the road. Photograph the plug before you disconnect it, so the wiring goes back in the same order.

Reading the PDC memory

Read the parking address with the manufacturer software and write the code texts on the sheet. The memory will name the sensor by position, and it will also carry an entry for the module itself when the fault is inside the unit. Read the live page as well, since it shows the distance each sensor is reporting at that moment.

Park the car with a clear space in front and behind, then read the distances with nothing near the bumpers. A good sensor reports a long distance and changes when you put your hand in front of it. A sensor that reports a short fixed distance with nothing there has failed, and that is the figure that names it. Repeat the reading at each corner with your hand held half a metre out, since a good sensor reacts at once and a lazy one takes a second or more. Write the pair of figures for every sensor on the sheet, because a sensor that is drifting sits close to its neighbours and only the comparison exposes it.

The sensor that kills the system

On this system one sensor that is shorted can take the whole chain down, which is why the driver hears nothing at all. Unplug the suspect sensor and read the memory again, since a system that comes back to life with one sensor removed has found its fault. Then plug it back in and watch the fault return to confirm it.

Look at the sensor face for stone damage and for paint, since a bumper painted with the sensors left in place blinds them. A sensor covered in paint reports a short distance all the time and the driver hears a continuous tone. Clean the face with water and a soft cloth before you condemn the part.

Testing a sensor by its click

Switch the system on and listen at each sensor in turn with a stethoscope or a length of hose held to the ear. A working sensor gives a faint and regular ticking as it fires. A sensor that is silent is not being driven, and the fault is in that sensor or in the wire that feeds it.

Work along the bumper and note each sensor on the sheet as ticking or silent. Then measure the supply at the silent one with the system on and a lamp as the load. A supply that is present with no ticking points at the sensor, and a supply that is missing points at the wire or at the module output for that channel. The click is faint, so work in a quiet corner of the workshop with the radio off and the engine stopped. On a car with eight sensors you hear the front four and then the rear four as the system cycles, and a gap in that cycle is the channel that is not firing.

Supply and earth at the module

Measure the permanent feed at the module plug with a lamp as the load, then measure the earth pin against the battery post. Check the fuse for that circuit by voltage drop across the blades, and check the earth point behind the boot trim for corrosion under the ring terminal. A module that browns out gives the silence the driver describes.

Wiggle the loom at the module plug while the tester shows the distances. A reading that jumps as the loom moves is a broken strand near the plug, and it usually fails where the harness passes the hinge of the boot lid. Repair the wire with a soldered joint and a sleeve, then repeat the distance test.

The speaker and the warning gong

The beeps come from a speaker that the module drives, and a dead speaker gives a silent system with a clean memory. Read the memory for a speaker fault, then measure the speaker winding at its plug and compare it with the figure in the data. A winding that reads open needs no further test.

Check the speaker mounting in the rear shelf or the boot trim, since a speaker that has come loose still works and sounds dull. Try a known good speaker on the plug for a moment, and listen for the beep. A system that beeps with the test speaker has found the fault, and the rest of the checks can stop there.

Bumper work and the final test

Before the bumper goes back, check each sensor sits square in its holder and that the seal is not pinched. A sensor pushed in at an angle reports the road surface as an obstacle and the driver hears beeps at random. Push each one home by hand and look at the gap around the face, which should be even all round.

Then test the system with the car running and the bumpers fitted, walking around the car at a metre and then at half a metre. Listen for the rate to change with the distance at each corner. Read the memory once more afterwards and write the sensor positions you changed on the sheet for the next visit. Check the bumper for a loose bracket as you walk, since a bumper that moves on its mounts changes the angle of a sensor and the system then reports the ground as an obstacle. A car that beeps at nothing on a rough road has a bracket problem and the sensors are fine.

What is measured on an E60 with silent parking sensors
SymptomLikely causeWhat is measured
Button lights, no beeps at allOne sensor shortedDistances in live data with the bumpers clear
Continuous tone in open spacePainted or damaged sensor faceDistance per sensor, face cleaned and checked
Silent at one corner onlySensor not being drivenClick test at each sensor, supply with a lamp
Works dry and fails in rainWater in the boot plugPlug and pins at the module behind the trim

Frequently Asked Questions

Can the car be driven with a dead sensor?

It drives normally and you park without the aid. The system is worth repairing, since a silent system gives no warning at all when a child walks behind the car.

Does the bumper have to come off?

The sensors are reached from behind the bumper on this car, and the bumper only comes off when a holder is broken. The click test finds the sensor before any trim is removed.

Why does one sensor silence the whole system?

The sensors are driven in a chain and a shorted one pulls the line down. Unplugging the suspect and reading the memory again shows that in a minute.

What proves the module is at fault?

A missing supply at a sensor that the module should drive, with a good feed and a clean earth at the module plug.

Related Services