An engine that cranks at normal speed and does not fire at all is a different fault from one that fires and then dies, because nothing is happening inside the cylinders. When the MSV70 has lost its alignment with the immobiliser, the unit withholds spark and injection while the starter still turns the engine. The spark test and the crank signal come before the alignment is discussed.
The starter turns at the usual speed and the engine never catches, not even for a second. That sound rules out a flat battery and a starter that is dragging, and it points at a unit that has decided not to fire. Ask whether the car was cranking before a repair and whether any unit was swapped.
Ask also whether the fuel pump can be heard at key on, because a pump that runs proves the unit is alive and has decided against spark rather than being dead. A pump that never runs sends you to the supply and to the relay first. The answer decides whether the alignment is even the right subject. Listen at the filler neck if the pump is quiet, and note whether it runs for a second and stops, since a pump that keeps running has a relay that is stuck.
Pull a coil, fit a spark tester and crank the engine with the tester grounded on the head. No spark at all on two different coils points at the unit or at its trigger, while a spark that jumps a good gap rules the ignition side out. Do not hold a coil in your hand while cranking.
Connect a noid light or a scope to an injector plug and crank again. An injector that never pulses while the ignition gives no spark either describes a unit that is holding both back. A unit that pulses the injectors and gives no spark has a different fault inside it, and the crank signal is checked next. An injector that pulses once and then stops describes a unit that fires and then loses its authorisation, which is a different entry in the memory.
Scope the crank sensor while the engine turns, because the unit needs a clean pattern before it will schedule a spark. A signal that is missing or ragged means the sensor or its gap is the fault, and none of the alignment work applies. Note the amplitude and the shape while cranking. Crank for at least three seconds so the trace has time to settle, since the first turn is often ragged on a cold engine and means nothing on its own.
Measure the main relay output at the unit with the key on and again while cranking, since a relay that drops out as the starter turns leaves the unit awake but unable to fire. A feed that sags with a bulb on it points at the relay contacts, and the relay is replaced before the unit is suspected. Watch the same feed on a scope through a whole crank, because a relay that chatters shows as a row of drops that a meter averages out and hides.
The engine unit and the immobiliser share a serial number, and the engine unit only fires while the two numbers agree. A rollback leaves the unit holding an older number than the one the immobiliser expects, so the unit answers the tester and refuses to fire. This happens after a swap and after a failed write.
The car does not report this as a wiring fault. It cranks, it does not fire, and the tester shows an entry about the start authorisation in the engine unit. Read that entry before you look at the coils again, because it decides the next step of the job. The entry may name the key, the unit or the authorisation itself, and the wording tells you which side of the pair to read first.
Open the engine unit and read the live values for the start authorisation while the key is turned. A unit that reports the authorisation as refused has told you where the fault is. Write the value down before you clear anything, since a cleared entry takes the evidence with it.
Then read the immobiliser address and confirm that the key is accepted there. A key that the immobiliser accepts and the engine unit refuses is the classic mismatch. A key that neither accepts is a key problem, and the second key test settles that in one minute. Do that test with the keys well apart, because a car that can read both at once reports a key present and then refuses to start, which sends you down the wrong path.
Measure the permanent and the ignition feeds at the engine unit connector with the plug fitted, using fine probes through the seal. Both should sit at battery level, and the ignition feed should hold while cranking. A feed that drops as the starter turns makes the unit reset at the worst moment.
Measure the ground pins against the battery post on the millivolt range. A drop above about fifty millivolts is enough to disturb the unit, and it also disturbs the coil earths, which are shared. Clean the studs and repeat both readings before any alignment work is planned.
A used engine unit carries the serial number of the car it came from, and it will not fire that car until the numbers are aligned. The same applies when the immobiliser is replaced. Neither unit works on its own, which is why the pair is treated together.
Save the data from both units before the alignment is written, because a write that fails leaves the pair out of step and the car unable to start at all. Keep a charger on the battery through the whole procedure, since the write takes long enough for a weak battery to fall away. Photograph both part numbers as well, because the pair that leaves the car must be the pair that goes back in, and a mixed set is the fault that arrives next month.
The alignment is the fault when the crank signal is clean, both feeds hold while cranking, the ground drop is low, the immobiliser accepts the key, and the engine unit reports the authorisation as refused. Those results together leave the pair as the repair rather than the ignition.
A unit that gives no spark and no injection pulse with a clean crank signal is behaving exactly as an immobilised unit does. Do not replace coils or a crank sensor on that evidence. Write each result on the sheet, and read the entries again after the alignment so the change is visible. A car that fires for a second and then dies has a different fault, and it belongs to the supply or to the crank signal rather than to the authorisation.
Read the start authorisation values before you touch the ignition side, because a car that cranks and does not fire with a clean crank signal is usually an immobiliser decision rather than a burnt coil. Scope the crank sensor and confirm the feeds hold while the starter turns. Then read both addresses and compare what each of them says about the key. A pair that disagrees is aligned, and a pair that agrees sends you back to the spark test with a clear answer.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Cranks, no fire, no codes on the dash | Start authorisation refused | Live value in the engine unit with the key turned |
| No spark and no injector pulse | Unit holding both back | Spark tester at two coils, noid light at an injector |
| Signal missing while cranking | Crank sensor or its gap | Scope trace of the crank sensor during the start |
| Unit resets as the starter turns | Main relay or a feed | Feed at the unit with a bulb fitted while cranking |
The starter is enabled on this car even when the start authorisation is refused, so the engine turns and never fires. The refusal is visible in the engine unit live values.
The pair is aligned through the diagnostic socket with a stable supply on the battery. A write that fails leaves the two numbers out of step, so the data is saved first.
A supply that falls away during a write can leave the unit holding an older number. The entry in the engine unit is read first, then the feeds are measured before the write is repeated.
The engine is started, the entries in both units are read again, and the key is cycled twice. A refusal that returns means the write did not take.