A screen that works with no sound at all points at the fibre ring behind the MMI, because the audio travels as light and not as current along a wire. One node that stops passing light takes the whole ring down and every unit behind it goes silent. The ring break diagnosis names the node before a panel comes off.
The screen works, the radio shows a station and the map draws, and nothing comes out of the speakers. That combination points at the ring rather than at the speakers or at the wiring to them, because a ring that has lost one node goes quiet as a whole. Ask when it started and whether work was done behind the dash before it.
Ask also whether the telephone still works and whether the parking sensors still beep, since those functions live on units that share the same ring. A car with no sound and a working phone has one node down, while a car with no sound and a dead phone has the break somewhere else on the loop. That answer narrows the search before you open a panel.
The ring is a loop of light that visits the head unit, the amplifier, the telephone unit and the navigation drive in a fixed order, and each unit passes the light on to the next. One node that stops passing light takes everything after it off the ring, which is why a single failed changer can silence a car that otherwise works.
Draw the order from the wiring diagram on the sheet before you touch anything, because the diagnosis depends on which units still answer. A unit that answers the tester has power and a working ring connection. A unit that does not answer is either that unit itself or the node in front of it, and the drawing tells you which of the two to test.
The information electronics address carries a ring break diagnosis that walks the loop and reports which node stopped passing light. Start it with the ignition on and the system awake, because it needs every unit powered to complete the walk. Write the reported node down, then confirm it with the light test before you trust it.
A diagnosis that names a node matches what you will find at that connector. A diagnosis that reports the ring as broken with no node named usually means two breaks or a unit with no supply at all. In that case the light test at each connector is the only way forward, and it is done one unit at a time from the head unit outwards.
Unplug one fibre connector at a time with the system awake and look into the end of the plug that comes from the previous unit. A working link shows a clear red light, and a dark end means the break is upstream of that point. Do this with the ignition on and keep your eye away from the ferrule while you look.
Work outwards from the head unit so each test tells you something new. The first dark connector you find sits just after the break, and the unit before it is the one to examine. Write the result for each connector on the sheet, because a break that moves after a connector is reseated points at a loose ferrule in the housing. A ferrule that pushes back when you seat it will let go again on the road.
A loop connector replaces a node in the ring and passes the light straight through, which takes a suspect unit out of the circuit without cutting anything. Fit the loop at the suspect unit and listen for the sound. Sound that returns proves the unit was taking the ring down, and silence proves the break is further back.
Do not leave a loop in a customer car for a road test unless you tell the owner what it does, because the functions of that unit stop working while it is fitted. Write the position of the loop on the sheet and remove it before the car leaves. A loop in place is a diagnosis, and the repair is the unit or its connector.
The amplifier needs a permanent feed, a wake up signal and a clean ground before it will pass light, and a missing wake up looks exactly like a dead amplifier. Measure the permanent feed at the connector with the ignition off, then the wake up with the system switched on. Both should sit at battery level.
A wake up that never arrives points at the head unit or at the wire between the two, and the amplifier is cleared of the fault. A wake up that arrives while the permanent feed holds leaves the amplifier itself as the suspect, and it goes to the bench with both voltages written on the note that travels with it.
The units in the glovebox and in the boot take water and heat, and they sit far enough along the ring that a fault there is easy to miss. Pull the connector and look for corrosion on the pins, then check the light at the plug that feeds the unit. A dark plug at that point means the ring stopped earlier.
Some of these cars left the factory without a changer and the ring is closed with a loop from new, so check the build list before you look for a unit that is not there. A missing unit with no loop in its place leaves the ring open, and the car has no sound until a loop is fitted in that position.
The repair is on the node that stopped passing light, and it covers the ferrule at the connector and the board behind it. A ferrule that is loose in its housing is replaced with the connector, and a board with a burnt receiver is repaired on the bench. Neither job needs the whole car to be present.
After the repair the ring is closed, the sound is tested from every source the car offers, and the fault memory of each unit on the ring is cleared. A unit that still stores a ring fault after the sound returns has a connector that is not fully seated, and that is found by pushing each plug home in turn. Listen at the amplifier for a click at switch on, because a unit that clicks has power and is only waiting for the ring.
Write the node order and the connector where the light stopped on the sheet, then add the result of the loop test beside it. Photograph the ferrule before it is cleaned, because a ferrule with a scratch on its face will fail again after a few months of vibration. Test the sound from every source before the trim goes back, including the telephone if the car carries one. A ring that comes back to life only with the trim refitted points at a connector that the panel loads when it is screwed down. Keep the fibre ends capped until they are mated, since dust on a ferrule face scatters the light and gives a ring fault that no tester will name.
| Symptom | Likely cause | What is measured |
|---|---|---|
| No sound while screen and radio work | One node not passing light | Red light at the plug feeding each unit |
| Ring diagnosed, no node named | Two breaks or a unit without supply | Light at each connector from the head unit out |
| Sound returns with a loop fitted | Unit taking the ring down | Loop test at the suspect node |
| Amplifier silent but powered | Wake up signal missing | Permanent feed and wake up at the amplifier |
The audio travels on the fibre ring and the display does not, so a ring that has lost one node leaves the screen working and the speakers silent. That is why the ring is tested before the speakers are.
The loop only bypasses the unit it is fitted to, so its functions stop working. It is a test that is removed once the result is written down, and the owner is told what it does.
The unit is coded to the car and the ring is closed again before the sound is tested. An amplifier fitted without coding answers on the tester and stays silent, which looks like a second fault.
With the light test at each connector, one at a time, working outwards from the head unit. The first dark connector sits just after the break, and the unit in front of it is the one to examine.