PGE Tuning Lab

Audi MMI navigation plus with no map on the A4 B8

On the A4 B8 the navigation plus keeps the map on an internal drive and reads it while the car moves, so the map can go missing without the radio losing a note. The screen then opens grey with the car arrow gone, or the unit reports that the navigation data is not available. The order below separates lost data from a drive that can no longer hold it.

What the screen does

The map page opens with no roads and no position, or the system reports that the navigation data is not available and offers no route. The radio still plays and the media still reads its card, and the telephone still pairs, which tells you the unit is awake and only the navigation side has gone. Ask when the map last worked, and write the date on the sheet.

Ask whether the battery was replaced or disconnected around the time the map went, because a write that was cut off leaves the database half finished and the unit behaves exactly like this. Ask too whether a card has been left in the slot since then. Photograph the screen while the message is up, since the exact wording decides which of the two faults you have.

What navigation plus holds

This unit reads the map from an internal drive while you drive, so a region with a bad block disappears first and the rest follows later. There is no disc to swap in normal use, and the map cannot be reloaded from a telephone or from a stick. That is why a map that worked last week and is gone today points at the drive or at the data itself. A drive that has been sluggish for months gives a map that redraws late before it gives a map that is gone.

The drive also holds the music library where the car has one, so ask whether the stored tracks have gone as well. A unit that has lost the map and kept the music has a database fault, and a unit that has lost both has a drive fault. That one question saves a good deal of time on the bench.

Reading the unit before anything

Open the infotainment address in the diagnostic session and read the fault memory before you clear anything. Entries about the navigation database and about a read error on the internal memory are the ones that matter here, with any entry about the drive beside them. Write each entry down with its frequency, because an entry that comes back after a clear is current.

Measure the permanent feed and the ignition feed at the unit connector with the plug fitted and fine probes through the seal, and measure the ground pins against the battery post on the millivolt range. A drop above fifty millivolts is enough to make the unit reset during a write and lose the data it was holding. Repeat both readings with the screen and the amplifier working.

Version and region

Open the version screen and read the database version, then compare it with the version that belongs to that car and that market. A unit holding a map for another region shows main roads where there are none and no detail at all where the car actually is. A version older than the last published update means the write never took. The market code sits beside the version, and a wrong code is corrected in the update menu before the data is loaded again.

Write the version on the sheet before the update and again afterwards, because the pair of numbers is the evidence that the install worked. A version that does not change after a completed install means the unit took the file and kept the old database. That points at the drive and at the memory behind it.

Reinstalling the map data

The map goes back from the card the update is published on, and the procedure is started from the update menu in the unit itself. Connect a charger and keep the ignition on through the whole write, because a unit that falls asleep halfway leaves the database in the state you are trying to cure. Do not open a door or touch the key while the progress bar moves.

Watch the progress figure and note where it stops if it stops, since the number is the most useful piece of evidence in the job. A write that reaches the same figure twice and stops there has told you the drive refuses that block. A write that stops at a different figure each time points at the card or at the reader.

When the install will not finish

A write that fails at the same point with two known good cards means the drive cannot take that block, and further attempts with other cards will not change it. Read the drive test where the tester offers one, and write down the result. A drive that reports bad blocks has answered the question and the unit comes out for repair.

A write that fails at a random point each time belongs to the card or to the supply. Clean the card contacts, try a second card that has worked in another car, and measure the feed at the unit with a scope during the write. A supply that dips as the amplifier cuts in will abort the install at a different place every time.

Supply, ground and the optical ring

Measure both feeds at the unit with the plug fitted and the ground pins on the millivolt range while the system is playing, since a load on the amplifier is when a poor ground shows. Then look at the fibre connector at the unit with the ignition on, because a red light at the port proves the ring is alive up to that point. No light means the ring is open somewhere behind it.

Work round the ring with a bypass loop at each module in turn, and watch the light return at the unit when the faulty module is taken out of the path. A module that has shut down takes the navigation with it on some builds of this system. Write down which module was bridged, since that module is the repair.

What confirms the unit

The unit is the fault when both feeds hold through a write, the ground drop is low, the ring is complete, the card is known good and the install still stops at the same block. Those results together leave the drive and the board, and the unit goes on the bench with the version written on the tag.

Write the version and the fault entries from before and after on the sheet. A map that comes back needs the position checked on a short drive, because a correct map with a wrong position is an antenna fault and the customer will be back within a week. Let the car stand overnight and open the map again from cold, then read the entries again after a few days of use.

Photograph the message on the screen before you touch anything, then read the fault memory and the database version in the same session. Put a charger on the car and let one install run to the end while you watch the progress figure. A write that stops at the same block with a good card has named the drive, and the bench settles it.

What is measured when the map has gone from navigation plus
SymptomLikely causeWhat is measured
Map grey, radio and telephone fineMap data missing from the driveDatabase version and entries in the infotainment address
Data gone after a battery jobWrite was interruptedFault memory read before the install is repeated
Install stops at the same blockDrive cannot take the writeProgress figure on two attempts with different cards
Unit drops off the ringOptical break or a dead moduleRed light at the fibre port, bypass loop at each module

Frequently Asked Questions

Can the map be loaded from a telephone or a memory stick?

The unit reads the data from the card the update is published on, and it will not take a copy placed on another medium. The install is started from the update menu inside the unit.

Does a battery disconnect wipe the map?

A clean disconnect leaves the data intact. A write cut off by a disconnect leaves the database half finished, and that shows as a missing map with entries in the unit.

Is a used unit a straight swap?

A used unit carries the coding and the protection data of the car it came from, so it needs coding and the protection released before the map appears. Both are read from the old unit first.

What is checked after the install?

The version is read back and compared, the position is checked on a short drive, and the entries are read again after a few days. A map that is present with a wrong position sends you to the antenna.

Related Services