An MMI 3G that never gets past a dark screen on an A4 B8 or a Q5 is often held down by the optical ring rather than by the head unit itself. The unit boots when every member of the ring passes light, so one dead module or one kinked fibre keeps the whole system off. The order below finds that member before you pull the head unit out.
The driver reports a black screen and no radio, and mentions that the parking tone has gone as well. On some cars the clock in the dash freezes at the time the unit stopped. Ask whether anything else went quiet at the same moment, and note it, because a telephone module that stopped working at the same instant points at the ring rather than at the screen.
Ask what happened before the fault. A battery that was disconnected, a jump start, or work behind the dashboard for a hands free kit all sit in front of this complaint on a regular basis. Write those answers next to the mileage, since a unit that lost its feed during a start is often healthy and the car is where the fault is. Note the battery voltage as it arrived too.
Read every address in the car, then open the head unit on its own and see whether it answers. A unit that answers with a dark screen has a live processor and the fault sits on the display or the boot side. A unit that does not answer has lost its feed or its wake path, and the dashboard stays together while you measure at the plug. Read it twice, once at key on and once a minute later.
Save the identification page before anything is unplugged, because the coding and the component protection data are read from it when a replacement is prepared. Write down the addresses that did answer as well, since several absent modules on the same bus send you to a shared feed before you reach for the head unit.
Measure the permanent feed and the ignition feed at the unit with the plug fitted, using fine probes down the back of the seal. Each pin should read at battery level with the ignition on. Load the permanent pin with a bulb and read it again, since a joint that shows twelve volts on an open circuit falls away under a small load and the unit never finishes a boot.
Put the meter on millivolts and read from the ground pins to the battery negative post with the ignition on. The figure should stay close to zero. A drop that rises as the screen tries to light explains a unit that flickers once and dies, because the processor resets when its reference moves under that load. Take the second reading with the panel awake.
Run the ring break diagnostic from the tester and read which member is reported as not passing light. That test names the unit that the ring cannot see through, and it is the fastest way into this fault. Write the order the ring reports, because the member in front of the break is where the fibre is checked.
Look at the fibre at each plug for a sharp bend, a crushed section under a trim panel or a grey patch where heat has hardened it. A fibre bent tighter than a fist will lose light and the ring drops out when the car warms. Check each connector for a latched shell, since a plug that is half home passes light on a cold morning. Push every one of them in until the latch clicks.
With the ignition on, look into the end of a fibre that you have unplugged at a module, keeping your eye off the axis. A red glow proves the transmitter in front of it is working. No glow proves that member is not sending, and the ring test result is read again against that finding.
Do that check at each plug in turn rather than at one, since a ring with two faults reports only the first break it meets. Write the result for every member on the sheet. A ring where every member sends light and the unit still stays dark has the fault at the head unit or in the ring wiring between them. A glow that is weak at one end tells you the fibre is tired.
The screen is a separate part on both cars and it reaches the head unit through a screened cable with a small connector at each end. A unit that answers and keeps its audio, while showing nothing, has a fault on that link. Unplug the cable at the panel and look for a bent pin or a green contact in the shell.
Refit the cable and press it home until the latch clicks, then cycle the ignition and watch the panel. A screen that lights after that reseat was never a coding problem, and no software work is needed on the car. Write the result down, since these links work loose after a dashboard repair.
On the bench the unit is fed at thirteen and a half volts and watched on the current meter at switch on. A unit that pulls a steady current and then settles has a live processor and a boot fault. One that pulls almost nothing has an open path on its supply side, and one that pulls hard has a short that shows as heat within a minute. Write that figure down.
Fit the unit into a car on the ring that is known to work, or feed it a ring signal on the bench, because a head unit that is alone on the ring will not boot however healthy it is. That test separates a dead unit from a car with a broken ring and it costs one plug. Keep it powered for a few minutes after it lights.
Refit the unit and connect the battery, then cycle the ignition several times, letting the screen settle at each key on before turning it again. Then check the radio, the navigation map and the parking tone, because a unit that lights and stays silent is still a fault on the audio side of the board.
Write the feed and ground values on the sheet with the ring test result and the bench figure, along with the coding that was written. That record is what makes a second visit short, since these systems come back after another flat battery and the numbers from the first visit are the quickest way to see it. Keep a copy with the unit if it travels.
Judge the repair in a dark workshop with the brightness turned down, because a backlight that is fading looks perfect in daylight and the driver returns with the same complaint. Shake the harness behind the dashboard while the screen is lit and read the feed again, since a drop that appears only when the harness moves belongs to a connector rather than to the board. Set the clock before the car leaves.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Dark at key on, no radio | Feed or wake missing at the unit | Both feed pins at the plug under load, ground drop |
| Other modules silent too | Ring member not passing light | Ring break diagnostic, then light at each fibre end |
| Unit answers, screen black | Display cable or panel | Screen cable reseated at both ends, then the feed at the panel |
| Lights on the bench, dark in the car | Car wiring or a broken ring | Feed and ground at the plug, unit in a known good car |
It drives, but there is no radio and no navigation, and the parking tone is gone as well. The ring test comes first, because a fault on the ring is fixed without touching the head unit.
The ring passes light from member to member, so an open ring stops the sequence and the head unit does not finish its boot. The diagnostic names the member that is not passing light.
The ring test is clean and every member sends light, yet the unit still stays dark. Feeding it in a car that is known to work confirms it before the case is opened.
It does, and the component protection is matched to the car before the unit works. The identification page is read first so the coding is written from the original data.