PGE Tuning Lab

Audi MMI 2G with no sound and no navigation on A6 C6

An A6 C6 with MMI 2G that has gone silent and lost its navigation usually has one node down on the optical ring, and the whole system then behaves as if it were switched off. The radio, the amplifier and the navigation drive all sit on that ring. The checks below find the node that broke it.

What the driver hears and sees

The screen lights up with the menu and the buttons still work, but no sound comes from any speaker and the navigation page never loads a map. Some drivers report that the radio shows a station name while the volume does nothing at all. Others say the system worked after a restart and died again later the same day. Write down when it started and whether it followed a flat battery or a repair in the boot.

Ask whether anything was loaded into the boot or the glovebox before the fault, since a plug knocked out of a module during loading breaks the ring. Ask whether a phone kit was fitted recently or a camera added, because a new node spliced into the ring with the wrong order stops the whole chain from waking. Note the exact build of the car from the label in the spare wheel well. Take a photograph of the boot trim before you remove it, because the clips on this car break easily and a loose panel will rattle for the rest of the car's life.

The ring and how one node shuts it down

The audio and navigation units are joined in one loop of optical fibre, and each module passes the light on to the next. When one node stops transmitting, everything downstream of it goes dark and the system reports the whole ring as faulty. That is why a dead navigation drive can take the sound with it, even though the amplifier is healthy.

The light travels in one direction only, so the order of the modules matters. Read the ring order from the wiring diagram for this car before you touch anything, then write that order on the sheet. A car with a module added at the end of the chain and not coded in will report faults that look like a broken fibre. The ring also carries the wake up message, so a node that has lost its supply stays dark and blocks every module behind it in the chain.

Reading the control head memory

Read the address for the control head with the dealer software and open the optical bus page inside that address. The memory lists each node by name and marks the one that failed to answer. Write that name on the sheet, since it is the starting point and it saves you pulling half the trim out of the car.

Note also whether the memory shows a wake up fault for the ring. A ring that never wakes points at the control head or at its supply, and a ring that wakes and then drops points at a node further along. Clear nothing before you have written both entries down, because the second one is often the useful one.

The red light test at each plug

With the ignition on, pull each optical plug in turn and look into the end of the fibre. A live transmitter shows a clear red glow at the plug you are holding. A plug with no glow means the module feeding it is dead or has lost its supply, and that module is the one to test next.

Work along the ring in order and stop at the first dark plug. Do not look into the fibre with your eye close to the end, since the light is bright and it is easy to hurt yourself. Write the result for each module on the sheet as you go, because the pattern of light and dark tells the story faster than any code. Use a clean cloth on the fibre end before you refit it, since dust on the face cuts the light down and makes a healthy node look weak.

Bridging a node out of the ring

Take the suspect node out of the loop with a bridging insert made for this connector, and switch the system on again. If the sound returns and the rest of the menu works, the node you bridged is the one that broke the ring. That single test separates a module fault from a fibre fault and it takes a minute. Keep the ignition off while you swap the insert, because the fibre ends are easily damaged by a careless push and a damaged end gives you a second fault to chase.

If the ring stays dark with the node bridged, move the bridge to the next module in the order and repeat. Keep the bridges in the same place until the system wakes, then note the last module you removed. The fibre itself can be broken inside the trim, and a bend tighter than the fibre allows will do it without any visible damage.

Supply and earth at the amplifier

The amplifier sits in the side panel of the boot and it needs a solid feed and a clean earth to pass the ring on. Measure the feed at its plug with the system switched on and a load applied, then measure the earth pin against the battery post. A feed that drops when the ring wakes is a tired relay or a corroded fuse holder.

Check the fuse for that circuit by voltage drop rather than by eye, then check the earth stud for corrosion under the ring terminal. A stud that looks tight can still carry a poor connection, and the amplifier will shut down when it draws current. Clean the stud, refit the terminal and test the ring again before you replace the unit.

The navigation drive and its disc

The navigation drive in the glovebox carries a laser that fails with age, and a drive that cannot read its disc will not join the ring. Listen for the drive spinning up when the system wakes, and feel the casing for the slight vibration it should make. A drive that is silent while the rest of the ring works has lost its supply or its motor.

Take the disc out and look at the surface in daylight. A disc with scratches on the data side or a film of dirt will fail to read in a drive that is otherwise good. Clean it with a soft cloth from the centre outwards, then try a known good disc before you condemn the drive. Write the disc version on the sheet, because a drive that reads the old disc and not the new one has a laser that is losing power.

Closing the ring and the final test

Refit every plug in the ring with a firm push until it clicks, and check that each fibre sits fully home in its housing. A plug that is in but not latched will work on the bench and fail on the road. Then switch the system on and let it run for ten minutes with the radio at a normal level.

Read the memory once more and confirm the optical page is clean. Test the navigation with a route across two towns so the drive has to read the map for a while, and test the phone and the CD changer if the car has them. A ring with one weak node often fails again within a week, so write the node you bridged on the sheet for the next visit. Ask the owner to report anything that returns within the month, since an intermittent node shows up on a rough road or in the rain rather than in the workshop.

What is measured on an A6 C6 with a silent MMI 2G system
SymptomLikely causeWhat is measured
No sound and no map, menu still shownOne node down on the ringOptical page in the control head memory, node name
System dead after a restartRing not waking at allFeed at the control head, red light at the first plug
Sound returns with a module bridgedFailed module or broken fibreBridge test in ring order, then the fibre under the trim
Navigation never loads, sound fineDrive that cannot read its discDisc surface in daylight, drive spin up on wake

Frequently Asked Questions

Can the car be used with the ring broken?

It drives normally, but you lose the sound and the navigation. A node that is shorting the ring can flatten the battery overnight, so it is worth finding.

Is the amplifier always the guilty part when the sound goes?

It is often blamed and rarely at fault. A dead navigation drive takes the sound with it on this ring, and the bridge test shows which node it is.

Does a used module need coding?

It needs to be matched to the car and placed in the ring order. A module from another car will otherwise report a component protection fault and stay silent.

What single test finds the break fastest?

The red light at each plug in ring order, stopped at the first dark one. It narrows a dozen modules down to one in a few minutes.

Related Services