A Passat B7 that shows a message about the key and refuses to start on the button still starts when the key is held against the marked spot on the column. That difference is the whole diagnosis in one sentence, because it separates the key from the antennas that read it. Read the Kessy address before you change a key.
The driver presses the button and nothing happens, then the cluster shows a message about the key. The car may start with the key held against the spot on the steering column, and it may start from the second key without a problem. Write down which key works and which one does not, since that answer decides the first measurement.
Ask whether the fault appears at one door and not at the other, or only when the key is in a bag or a pocket. A car that reads through one handle and not the other has a fault at that handle, and a car that reads nowhere has a fault at the unit or at the antennas inside the cabin. A key kept beside a phone in the same pocket gives a message of its own, and the driver usually mentions it when you ask where the key lives.
Read the Kessy address and save the memory before anything else, because the entries name the antenna that failed to read the key. An entry for one antenna sends you to that part of the car and leaves the other three alone. Write the entries out in the order they are stamped, since the newest entry is often the one that matches the complaint.
Check the other addresses as well, because a Kessy unit that has lost its supply takes the central locking and the interior lights with it. A car with one fault on the Kessy address and everything else working has a fault on the reading side, and the car can still be locked with the blade in the door.
Measure the coin cell in the key under a load of about one kilo ohm and read the value, because a cell that shows three volts open can fall to two under that load. A key with a weak cell still starts the car when it is held against the reader coil, since that coil powers the transponder. Replace the cell and try the button again.
Look at the key for a crack in the housing and for a button that stays pressed, because a button held down flattens the cell and keeps the key awake. A key that has been through a washing machine gives the same message as a key with a dead cell, and the second key in the drawer tells you which of the two you have. Write the cell value and the serial of the key on the sheet, since a key that comes back a month later is compared on those numbers.
Measure the resistance of each interior antenna at its connector and compare the values with each other, because a broken winding reads open and a shorted one reads low. A reading that stands out from the other antennas names the part. Look at the connector under the console as well, since a plug that is not latched gives the same result.
Put a pickup coil on the scope near an antenna and press the button, then watch for the burst of low frequency energy that the unit sends out. A burst at one antenna and nothing at the next one separates a dead antenna from a unit that has stopped driving them. Write the result for each antenna on the sheet.
A handle that reads nothing stops the car from unlocking on approach, and the driver then reports a key that is not detected. Pull the handle and watch the value in the data page, since the sensor either changes state or it does not. A handle that never changes state has a sensor or a wire in the door.
Open the door and look at the plug inside the door shell for water, because the handle sits where the rain runs and the seal fails with age. Dry the plug and repeat the test before the handle is ordered. A handle that works after the plug is dried will fail again in the next storm, so write that down as well. Grease the plug with a contact grease and refit it with the boot seated the right way round.
Measure the permanent feed and the ignition feed at the Kessy unit connector with the plug fitted, then load each one with a bulb. A unit that sees a feed that sags during a start can lose the reading of the key at exactly the moment the driver presses the button. Write the loaded values on the sheet.
Measure the ground pins to the battery post on the millivolt range, then clean the stud and read them again. A drop above about fifty millivolts disturbs the low frequency driver and the antennas go quiet, which reads on the tester as four antenna faults at once. That pattern points at the unit and its ground. Check the supply again after the ground is cleaned, because a unit with a poor ground pulls more current through the feed and the value moves.
Read the entries for the steering lock as well, because a lock that has not released stops the start and the cluster may show a message about the steering. Turn the wheel gently while the button is pressed, since a lock that is jammed releases at one point of that movement and the car then starts.
A lock that stays engaged gives a car that will not start with a key that is read correctly, and that is a different repair from this one. Write both results on the sheet, since a car with two faults is common and the second one shows up after the first is repaired.
Fit the parts, clear the memory and press the button with each key in turn, then lock and unlock the car from both front handles. Watch the interior lights at the same time, because a unit that reads the key and fails to wake the car has a fault on the locking side. Write the result for each key.
Ask for both keys at the start of the job, because a second key that was never presented comes back as a complaint about the repair. Match the keys in the same session if the unit has been replaced, and check the emergency start with each one before the car leaves. Note the key count on the sheet so the next reader knows how many keys the car had when it arrived.
Hold the key against the marked spot on the column before you open anything, because a car that starts there has a working transponder and the fault sits with the antennas that read it at a distance. Then measure the cell in the key under a load, since a weak cell gives a fault that looks exactly like a dead antenna. Write the antenna values down as you take them, because a unit that has stopped driving them all at once is a different repair from one dead winding and the numbers are what separates the two.
| Symptom | Likely cause | What is measured |
|---|---|---|
| No start on the button, starts at the column | Weak cell in the key | Cell voltage under a one kilo ohm load |
| One door does not unlock | Handle sensor or its plug | Value on the data page while the handle is pulled |
| Four antenna entries at once | Unit or its ground | Millivolt drop at the unit ground pins |
| Key read, no crank | Steering lock not released | Lock entry and the wheel movement during a press |
The reader coil at that spot powers the transponder in the key, so the key works even with a flat cell. That result points at the antennas that read the key at a distance.
It can, because a cell that falls under load stops the key from answering the unit. The cell is measured with a load on it before any part is ordered.
The unit is coded to the car and the keys are matched to it in the same session. Both keys are presented before the car leaves, since a key left at home comes back as a fault.
Each antenna is measured at its connector and the readings are compared with each other, then a pickup coil on the scope shows whether the unit drives it. A reading that stands out names the part.