A warning lamp on the dash and heavy steering at walking pace on a car with electric assist usually leads to the J500 unit mounted on the steering rack. The unit reads the torque in the column and drives the motor, so a fault in either path lights the same lamp. The feeds at the rack are measured before the unit is blamed.
The owner reports that the wheel goes heavy at idle and in a car park, and that the lamp stays on after a restart or comes back after a short drive. Above walking pace the car feels almost normal, because the assist is needed least where the fault is worst. That is why the complaint often waits until a parking manoeuvre brings it out.
Read the steering assist address and write the entries out as the tester prints them. A unit with a motor current fault stores an entry for that current, and a unit with a signal fault stores an entry that names the sensor. Clear the memory and sweep the wheel from lock to lock with the engine running. An entry that returns during that sweep describes a fault that is present under load, while an entry that returns only after a cold start describes a supply that sags before the alternator charges.
Measure the heavy feed at the unit connector with the ignition off, using a probe rated for the current path and the battery negative post as your reference. Then measure the ignition feed with the key on. Both should sit at battery level, and the heavy feed should hold that value while an assistant turns the wheel against the stops.
A heavy feed that falls away during a steering sweep points at the fuse holder or at the cable from the battery, and the unit is cleared of that complaint. Look at the fuse for a hairline crack and at the cable lug for corrosion under the insulation. Both faults behave like a failed unit until they are measured with the motor pulling current through them.
The rack is earthed through a strap to the body, and that strap carries the full motor current. Measure the voltage between the rack housing and the battery negative post while the wheel is turned against a stop on a warm engine. A reading above about three tenths of a volt means the strap or its mounting bolts are the fault.
Clean the bolt faces and repeat the measurement on the same points so the change is visible in your notes. A drop that falls to almost nothing confirms the repair, and the lamp should stay off through a full sweep afterwards. A drop that stays high with clean faces points at the cable itself, which is replaced before any work on the unit is planned.
Clamp a current probe around the heavy feed and read the draw with the engine idling and the wheel held slightly off centre. A healthy unit draws a steady current that rises as you load the wheel. A unit that pulls a large current with the wheel straight has a motor or a driver fault inside it, and the reading is the first evidence of that.
Watch the current at the moment the lamp comes on, because a unit that cuts the assist does so when its own current limit is reached. A cut that happens at a low current points at the measurement inside the unit rather than at the motor. Note that value on the sheet before the rack comes out of the car.
The torque sensor in the column is fed from the unit and returns two signals that move in opposite directions as the wheel is turned. Back probe those pins with the key on and read both with the wheel still. Each should sit near half of the reference, and a signal stuck at the top of its range is the fault you are looking for.
Turn the wheel slowly while an assistant reads both values. The two should move together and cross in the middle as the direction changes. One signal that moves while the other stays put confirms a sensor fault inside the column, and the unit is left alone until the column is sorted, which saves an unnecessary unit repair.
The motor connector on the rack faces the road and takes water from the wheel arch liner and from a blocked scuttle drain. Unplug it and look inside for water and for a white bloom on the pins. A connector with water in it gives faults that come and go with the weather, which is why the car often arrives on a dry day with nothing stored.
Dry the connector, clean the pins and repeat the current measurements on the same points. If the lamp stays off through a wet week of use, the housing seal was the repair. If the fault returns with the first rain, the motor windings have taken water and the rack is replaced as a complete unit with the coding written afterwards.
The fault is inside the J500 when both feeds hold under load, the ground drop is low, the current cut happens at a low value, and both torque signals move in the way they should. Those results together leave the unit as the only part still standing. Each of them rules out a cheaper repair on the way, and each is recorded on the sheet.
On the bench the unit is fed at thirteen and a half volts and the motor is loaded through a resistor bank while the current is logged. A unit that cuts out at a fraction of its rated current confirms the internal fault. A unit that runs and cuts at the right point sends you back to the column sensor with a clear result to report.
Turn the wheel from lock to lock three times with the engine running and watch the lamp, then repeat the sweep with the car rolling slowly in a yard. A lamp that stays off through both sweeps is the result you want. Keep the wheel off the stops during the second sweep, since the stop itself loads the motor hard.
Write the feed voltages and the ground drop on the sheet so the next visit starts from those numbers. Add the current you read at the moment of the cut. Tell the owner which of the two complaints brought the car in, because a heavy wheel at idle and a lamp on the dash can come from different faults on the same rack.
Do not condemn the rack before the ground strap has been measured under load, because a strap with a corroded bolt behaves exactly like an assist unit that has failed. The drop is read while the motor pulls current, which means a helper at the wheel and the meter on the millivolt range at the same moment. Write that number down. A car that recovers its assist after the strap is cleaned needs no work on the unit at all.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Heavy wheel at idle, lamp on | Ground strap or its bolts | Millivolt drop from rack housing to battery post |
| Assist cuts mid sweep | Motor current limit reached | Current on the heavy feed during the sweep |
| Lamp on at key on, wheel still | Feed missing at the unit | Both feeds at the rack connector |
| Fault returns after rain | Water in the motor connector | Pin condition inside the connector |
The assist is needed most when the car is hardly moving, so a unit that has cut its current leaves the wheel heavy in a car park. At speed the wheel needs little help, which hides the fault from the driver.
The car still steers because the column and the rack are joined mechanically, and the effort goes up at low speed. Send the owner out with that in mind and book the measurement, because a unit that keeps cutting may stop assisting altogether.
A supply that sags at a cold start can make the unit fail its self test and light the lamp. The feeds are measured with the plug fitted and again while the wheel is turned, so a sagging supply shows before the unit is opened.
The steering angle sensor is read and the coding is written, then the wheel is swept from lock to lock with the engine running. Note the current on the new rack at the same point of the sweep so the sheet carries a reference value.