PGE Tuning Lab

Mercedes W204 key not recognised with the steering lock released

A W204 that will not start because the key is not recognised often arrives with the steering lock already released, which confuses the owner because the wheel turns freely while nothing happens at the switch. On this car the ignition lock reads the key and passes the authorisation to the engine unit, and the lock motor has its own state. The checks below follow that chain from the key slot to the starter.

What the driver reports

The key goes into the slot and the dash stays mostly dark. The display tells the driver the key is not recognised. The steering wheel turns as if the car were unlocked, and the owner takes that as proof the ignition is on. Some report that the car started fine in the morning and refused in the afternoon with no warning at all, and others say it failed after the car stood for a week in the cold.

Ask whether the second key behaves the same way, since a fault that follows one key is a key problem and a fault that follows the car is a lock problem. Ask whether anything was spilled near the slot or whether the car has been valeted recently, because liquid reaches the reader coil through the trim. Write the mileage and the state of the key battery on the sheet before you begin.

Terminals and what the key should switch

Watch the dash while the key is inserted. Terminal 15 should come on and the warning lamps should light for their self test, then terminal 50 should crank when the key is turned. A car where terminal 15 never arrives has not accepted the key, and the starter is not being asked to turn. That single observation separates an authorisation fault from a starter circuit fault.

Read the terminal status page in the tester while a helper turns the key. You want to see the terminals change in order and stay on. A status that flickers back to off as the key is held has a supply that cannot carry the lock current, and the fault is in the wiring before it is in the unit. Write each terminal state down as it appears.

Reading the EZS memory

Read the ignition lock address with Xentry and write the code texts on the sheet as they appear. The memory will name the key as not recognised or name the steering lock as the blocking part, and the two send you to different places. Read the freeze frame too, since it carries the terminal states at the moment the fault set and those states are worth more than the code.

Open the page that shows the key status and the lock position together. A lock that reports released while the key is refused means the two parts disagree about where the car is in the start sequence. Clear nothing yet, because a cleared memory on this car can leave the lock in a state that takes a full cycle to recover. Read the page again after a key cycle and compare the two sets of values, since a status that changes on the second read is often the one worth chasing.

Supply and earth at the EZS

Pull the plug from the lock and measure the permanent feed and the ignition feed with a lamp as the load. Then measure the earth pin against the battery post with the meter set to volts while a helper cranks, since a volt drop on that path shows as a reading where you want near zero. A lock that browns out during cranking loses the key it has just read.

Check the fuses for those circuits by voltage drop across the blades, then look into the plug for a pin that has been pushed back. On this car the plug sits where a knee can reach it during a repair, and a pin that is in but not latched will work on the bench and fail once the trim is pressed home. Push each pin in with the proper tool and check the latch.

The key, its battery and the coil

Measure the reader coil at its plug and compare the reading with the figure in the repair data. A coil that reads open will never power a transponder, and a lock changed for a display fault will take the blame for a coil that was failing all along. Look at the coil winding through the slot with a light, since a broken winding is sometimes visible at the edge.

Try the key in the slot with the battery out of the key on a car with keyless entry, then repeat with a fresh battery. A key that works with a new cell was never a lock fault, and the owner has been chasing the wrong part. Hold the key still for a few seconds after insertion, because the lock reads it twice and a key that moves can fail the second read.

The steering lock and its motor

The lock motor runs for a moment when the key is accepted, and its current can be watched on a clamp while a helper inserts the key. A motor that draws current and does not move has a jammed pin or a worn gear, and a motor that draws nothing has no command or no supply. Listen for the sound at the column, since a healthy lock gives a short and definite click.

Read the lock position in the tester after the key is inserted and again after it is removed. A position that stays released with the key out means the lock cannot park itself, and the car will refuse the next start. Check the column for a mechanical bind by turning the wheel against the lock, then repeat the test before you condemn the motor.

The drive authorisation chain

The lock passes the authorisation to the engine unit over the data bus, and the engine unit answers. Read both addresses and compare the status each one reports. A lock that says the key is valid while the engine unit says it never received the release points at the bus or at the engine unit, and the lock is then doing its job.

Scope the bus at the lock plug while the key is turned, and look for activity at the moment the key is read. A quiet bus with a key inserted means the lock is not transmitting, which puts the fault inside the lock. Activity with no release at the engine unit sends you along the bus to the unit that is not answering.

The first start and the checks after

Pair the lock only with the workshop account online and the owner documents on file, because this part carries the identity the car was built with. Connect a charger before the routine, keep the key in the slot until the software confirms, and do not interrupt the cycle. A dip in the middle of the pairing leaves the car in a worse state than it arrived in.

Start the car and let it idle, then switch off and repeat from cold after the car has stood. Watch the lock position and the terminal states on both starts. A car that starts twice with a clean status and a lock that parks itself is repaired, and the sheet should carry the key count and the lock part number for the next visit.

What is measured on a W204 whose key is not recognised
SymptomLikely causeWhat is measured
Dash dark, key refused, wheel turnsLock that has not accepted the keyKey status and lock position in the lock address
Terminals flicker as the key is heldSupply that cannot carry the loadFeeds at the plug with a lamp, earth volt drop while cranking
One key fails, the other worksTransponder or key cellBoth keys in the slot, cell changed and the key held still
Lock stays released with the key outJammed pin or worn lock motorMotor current on a clamp, lock position after removal

Frequently Asked Questions

Can the car be pushed with the lock released?

The wheel turns and the car can be moved, but the engine will not run. Treat it as a car that has to be recovered to the workshop.

Does a new key solve a recognised key fault?

Only when the fault follows one key. A key that is refused by the car on both keys is a lock or a bus fault, and a new key changes nothing.

Can the lock be paired without the online account?

The routine needs the workshop account and the owner documents on file. Anything less leaves a part that starts once and refuses the next time.

Why check the coil before the lock itself?

A coil that reads open gives the same refusal as a failed lock and it is quick to rule out. The reading at the plug settles it in a minute, and that minute decides whether the lock comes out at all.

Related Services