PGE Tuning Lab

BMW EPS torque sensor faults on the E90 and the F30

A heavy wheel on an E90 or F30 with the EPS lamp on often comes from the torque sensor in the column, because the unit needs that signal before it assists at all. The sensor returns two signals that move in opposite directions, so one bad channel shows as a wheel that is heavy in one direction. The reference and both signals are measured before the column is disturbed.

How the driver describes it

The owner says the wheel is heavy at parking speed and that the lamp comes on now and then, usually after a slow manoeuvre. Some report that the wheel pulls to one side when the assist comes and goes, which is the sign of one channel drifting. Ask which direction feels heavier, since that answer points at the signal to measure first.

Ask whether the heaviness arrived suddenly or grew over a month. A sudden change follows a repair, a jump start or a kerb strike, and each of those sends you to a different place on the car. A gradual change is the pattern of a sensor that has worn, and the live values show it before any fault code is stored.

Fault memory and live values

Read the EPS address and write the entries out as the tester prints them. A stored torque fault may describe a signal outside its range, and the same entry can appear after a battery disconnect with nothing wrong, so clear the memory and drive the car before you believe it. Then open the live values with the wheel straight ahead.

With the wheel still, both torque signals should sit near the middle of their range and the angle value should read close to zero. A torque value that sits at the top of its range with the wheel straight describes a sensor that has failed or a column that a joint is loading. Note both numbers before you turn the wheel, and keep the engine running during that read, since the assist behaves differently when the charging voltage is low.

The five volt reference and the ground

Back probe the sensor plug with the key on and measure the reference against the sensor ground. The reference should read close to five volts and should not move when the wheel is turned. A reference that sags as the wheel moves points at the supply inside the unit rather than at the sensor itself.

Measure the sensor ground against the battery post on the millivolt range with the plug fitted. A ground that sits above about fifty millivolts adds an offset to both signals and makes a healthy sensor look faulty. That reading only means something with the connector in place, because the sensor ground carries no current once the plug is off.

The two torque signals at the plug

The sensor returns two signals that move in opposite directions, and their sum stays roughly constant as the wheel turns. Measure both at rest and write them down, then turn the wheel a quarter turn each way and measure again. The two values should move apart while their sum stays where it was.

One signal that stays at its rest value while the other moves is an open channel, and the sensor is the fault. Both signals that move in the same direction at once describe a wiring fault between the plug and the unit. A short between the two signal wires gives that pattern, and it is found with the plug disconnected at both ends.

Plausibility while the wheel turns

Watch both signals on a scope while an assistant turns the wheel slowly from lock to lock. The traces should cross in the middle in a smooth line, with no step and no flat spot. A step in one trace describes a worn track inside the sensor, and it appears at the same angle every time you sweep the wheel.

A flat spot at the straight ahead position matters most, because the unit needs a clean signal there before it will assist. If the flat spot shows in the live values and in the scope trace at the same angle, the sensor is worn and the column is the repair. Write the angle down so the next reader can repeat the sweep.

The angle sensor the unit also reads

The unit needs a steering angle as well as a torque value before it decides how much assist to give. Open that live value and turn the wheel one full turn each way. The angle should climb and fall smoothly and come back to near zero with the wheel straight.

An angle that jumps in steps of several degrees describes a dirty track, and the unit reduces the assist when the angle and the torque disagree. That disagreement is what stores the plausibility entry. Clear it and repeat a slow sweep before anything is replaced, because a plausibility entry alone does not prove a failed part. A car that has just had its tracking set can store the same entry, so ask about the last visit to a tyre shop.

Column joints and the intermediate shaft

The lower joint on the intermediate shaft seizes and adds drag that the sensor reads as driver torque, so the unit assists in the wrong direction and then cuts out. Check that joint with the front wheels off the ground and the steering lock released. The wheel should turn with light effort and without a stiff spot.

A stiff spot at one angle is a joint or a rack, and the sensor is not the fault even when its live value looks wrong. Disconnect the lower joint and turn the wheel again. A wheel that frees up with the joint off puts the fault on the shaft, and the sensor values are then read a second time. A shaft that has been hit from below holds the joint at an angle, and the stiffness comes back within a week.

What the readings confirm

The sensor is the fault when the reference holds, the sensor ground is low, one channel stays at its rest value, and the other channel moves in a smooth line. Those results together leave the column as the repair. A signal that steps at one angle adds a further result that points at the track inside the sensor.

On the bench the column is driven through its travel with the sensor powered at five volts and both outputs logged. A trace that steps at the same angle on two runs confirms the wear. A trace that is clean on the bench and faulty in the car sends you back to the ground stud and to the plug.

Measure the sensor ground before you condemn the column, because a ground that has crept up adds an offset to both channels and produces a live value that looks like a worn track. Read it on the millivolt range with the plug fitted and the key on. Note the reference and both signal values on the sheet in that order. A column that tests clean on the bench and misbehaves in the car usually has a connector that the column bracket loads when the trim is screwed down. Read both signals once more with the car on its wheels and the wheel straight, since a column that was loaded on a lift settles after the first turn.

What is measured on an EPS with heavy steering and a torque fault
SymptomLikely causeWhat is measured
Heavy in one direction onlyOne channel failed or wornBoth signals at rest and at a quarter turn each way
Assist cuts on a slow sweepFlat spot at straight aheadScope trace through the straight ahead angle
Plausibility entry with clean signalsAngle and torque disagreeAngle value over one turn each way
Stiff spot at one angleLower joint or the rackEffort with the front wheels off the ground

Frequently Asked Questions

Why is the wheel heavy in one direction only?

The two torque signals move in opposite directions, so one channel that has failed biases the value to one side. The unit then assists in the wrong direction and cuts out, which the driver feels as a heavy side.

Can the torque sensor be replaced on its own?

On some columns the sensor is a separate part and on others it is built into the column, so the part number decides. The reference and the ground are measured either way before the column comes out.

Does a battery disconnect cause this fault?

It can store a plausibility entry that reads like a sensor fault. The memory is cleared and the car driven before the sensor is condemned, and an entry that stays away is not a fault.

What is checked after a column is replaced?

The angle value is read and the coding is written, then the wheel is swept and both torque signals are read again. A column that reads near the middle at rest is the result you are looking for.

Related Services