PGE Tuning Lab

BMW EKP fuel pump control on the E90 and E70

A car that starts from cold every morning and refuses to restart after a short stop is a familiar arrival on these two models. The engine unit asks for fuel and the EKP module drives the pump, and either of them can let the car down once the back of the car is warm. The order below measures the request and the current before anything is replaced.

The hot no start story

The car runs perfectly from cold, is stopped for ten minutes outside a shop, and then cranks without firing. Half an hour later it starts as though nothing had happened, and the customer arrives with a story that sounds like a sensor on its way out. That pattern belongs to the fuel supply on this platform, and the module that drives the pump is where the measurement starts.

Ask how long the wait has to be and whether the engine has ever died while driving. A car that dies at speed and restarts after a wait points at the module cutting its output under load. A car that only refuses a hot restart points at a pump that has bound up as the heat soaked into it. A car that has been idling in traffic before the stop is the classic case.

Where the module sits and what it drives

The EKP sits near the tank on the E90 and behind the trim in the boot on the E70, and it drives the pump with a duty cycle the engine unit asks for. It is a control module with electronics inside, so it fails in ways a relay never could. The case sits close to the tank and takes the heat the fuel gives off as well as the heat of its own work. Read the part number on the case and write it down before anything is ordered.

The module reports its state to the engine unit, so it appears in the fault memory of the DME as well as in its own address. Read both before you clear anything. Access on the E70 is behind the boot trim and the connector sits where you can reach it with the pump running, which is exactly what the tests below need.

Reading the request

Backprobe the command wire between the engine unit and the module and scope it while the engine cranks. A square wave with a varying duty proves the engine unit is asking for fuel and moves the job to the module and to the pump. A flat line means the engine unit has decided not to ask, and the crank signal is checked before the pump.

Note the duty figure at key on and again during the crank, because the engine unit ramps the pump up as the starter turns. A request that rises and stays high while the pump stays silent has told you the module is not answering it. A request that is present at key on and gone once the starter turns points at the engine unit losing its crank reference. Write both figures on the sheet next to the battery voltage.

Measuring the pump current

Clamp the feed wire at the module output and read the current with the pump running, then repeat the reading after a hot soak. A pump drawing well above its normal few amps is worn, and the module protects itself by cutting the output when it gets there. Read the figure within the first seconds and again after a minute, since a worn pump climbs as it runs. That is the fault that only shows itself once the car is hot.

Measure the voltage at the pump connector while the pump runs, with the meter across the two pins of the plug and the plug still connected. A voltage far below battery level means resistance in the wire or in the module output stage, and the drop is followed along the wire to find where it sits. A pump that sees battery voltage and draws no current is open circuit.

Pressure at the rail

Fit a gauge at the rail test port and watch it while the engine cranks from cold, then repeat the test when the engine is hot. A rail that builds its value from cold and stays at zero when hot has confirmed a supply fault in one test. Read the live pressure in the engine unit as well, since the gauge and the sensor should agree.

A gauge that shows pressure while the engine unit reports zero is a sensor fault, and the pump is not the subject of the job. Compare the two readings before the module is blamed. A rail that holds its pressure after the key is switched off rules the pump out completely, and that check is worth doing with the engine warm since a leaking valve shows best at temperature.

The feed and the ground

Measure the permanent feed at the module connector with the plug fitted and fine probes through the seal, then measure it again while the pump runs. A feed that drops under that load points at the supply stud or at a fuse contact, and the drop is measured across the fuse blades themselves while current flows.

Measure the module ground against the battery post on the millivolt range with the pump running. A drop above fifty millivolts disturbs the module and slows the pump, and on a road test it reads like a pump that is failing. Clean the stud and repeat the reading before any part is ordered.

The hot soak test

Run the engine until the fan has cycled twice. Switch off and wait ten minutes with the bonnet closed. Then crank and watch the current clamp and the rail gauge at the same time. A pump that draws a rising current and then loses its feed has reproduced the complaint in the workshop, which is worth more than any stored entry. Write down how long the car stood before it refused, since that number tells you how far the heat has to travel.

Repeat the test with the module cooled by a damp rag laid on its case. A car that starts with the module cooled and refuses with it hot has placed the fault inside the module. The test takes a few minutes and it settles the argument before a part is ordered.

What confirms the module

The module is the fault when the request is present at its input, the feeds and grounds hold under load, the pump draws a normal current from cold and the output dies when the module is hot. Those results together leave the electronics inside the case, and the module goes on the bench for a load test.

Write the current and the duty figures from cold and from hot on the sheet, because that pair is the evidence for the repair. Fit a new pump where the current was high, since a module replaced on its own will fail again behind a worn pump. Repeat the soak test before the car goes back to the customer, then drive it and let it stand warm once more.

Scope the request wire first, because a command that never arrives sends you to the engine unit and to the crank signal. Then clamp the pump feed and read the current cold and again after a soak. A current that climbs as the car warms and an output that dies with it have named the pump and the module, and both are replaced together.

What is measured when an E90 or E70 will not start when hot
SymptomLikely causeWhat is measured
Starts cold, refuses a hot restartModule cutting its outputPump current and duty at the module, cold and hot
Pump draws a high current when hotWorn pump motorClamp on the module output after a soak
No command at the moduleEngine unit or crank signalScope on the request wire during the crank
Rail at zero, battery voltage at the pumpPump open circuitResistance at the pump plug, gauge at the rail

Frequently Asked Questions

Why does the car start again after half an hour?

The module cools and its output comes back, or the pump frees itself as the fuel around it cools. Both give a car that behaves until the next short stop.

Can the module be tested without the pump?

The output is loaded with a test lamp or a known good pump and the duty is watched. An output that dies under that load with the request present is failing inside the module.

Does a weak battery cause this?

A supply that sags during the crank makes the module drop its output, and the fault then looks thermal. The battery is measured under load and the feed is checked while cranking.

What is done after the repair?

The soak test is repeated twice, the entries are read again, and the rail pressure is watched through a hot restart. A current that is still high means the pump was not the only problem.

Related Services