PGE Tuning Lab

VW DQ200 shudder when pulling away on the Golf 6

A Golf 6 that judders as it moves off from a standstill is usually reported as a clutch on the way out, and often the pack still has life in it. The dry DQ200 keeps a kiss point and a friction map in the mechatronic unit, and both drift as the pack beds in. The adaptation run and the stored values decide which of the two you are looking at.

What the driver describes

The car shakes as it takes up drive in first and again in reverse, and the shake is worse when the gearbox is hot after a run through traffic. Once the car is rolling, the shifts are clean and the shake disappears. Ask whether it appears on a hill, with a load in the car, or only on a light throttle, since those answers separate the pack from the engine. The shake usually shows best on a slight incline, where the clutch slips longer before it locks.

Ask also when the gearbox last had a clutch adaptation run and whether the mechatronic unit has been replaced, because a new unit arrives without the values the old one held. A car that shakes after a unit swap starts from a different place than one that has shaken for months. Write the mileage next to the answer on the sheet, since a car still on its first pack at low mileage is more likely to need the run than a new clutch.

The gearbox and what it holds

The DQ200 is the seven speed dry unit, so the packs run in air and the oil in the housing serves the mechatronic unit and the gears. The level matters more than the colour, and a low level shows as a harsh engagement before it shows as a shake. Check the level at the fill plug at the temperature the maker states. Top up with the specified fluid only, because the unit is sensitive to the wrong oil and will shift poorly on it.

Read the gearbox identification and the software version in the unit before anything else, since a car that has been flashed with the wrong file can hold a map that no adaptation will suit. Note the version on the sheet. A version that does not match the car is corrected first, and the adaptation is run afterwards.

Engine side ruled out first

A misfire at idle feels like a clutch shake once the car is loaded, so run a smooth running comparison before the gearbox is opened. Read the misfire counters on a road test with the throttle held light in a high gear, and watch the values as the engine labours. A cylinder that counts up under load is the fault, and the pack is innocent.

Check the dual mass flywheel for backlash through the starter aperture with a probe, since a worn flywheel gives the same shake at the same moment of take up. The engine mounts belong in that check too, because a mount that has collapsed lets the engine rock as the clutch comes in. Both are ruled out before a pack is ordered.

Reading the clutch values

Open the gearbox measuring blocks and read the adaptation values for both clutches with the ignition on and the engine idling. Each clutch stores its own travel figure for the kiss point, and the two numbers usually differ. Write both down before anything is run, because the adaptation run overwrites them. The values are read with the engine idling so the unit has pressure and both packs sit at their rest point.

Compare each value against the wear limit the tester shows for that unit. A value sitting close to the limit means the pack has travelled as far as it can and no run will recover the take up. A value in the middle of the range points at a lost adaptation and at a shake that a run can cure.

The adaptation run

Bring the gearbox to its working temperature first, because the run is refused outside the window the tester needs. Select the basic setting for the clutch adaptation and follow the prompts to the end without touching the throttle or the brake. The unit drives both clutches through their travel and stores a fresh kiss point.

Listen to the gearbox through the run, since a pack that is badly worn makes a noise the tester never reports. Watch the oil temperature while the run goes, because a car that idles for ten minutes in a warm workshop can fall out of the window and abort. Run it once more if the tester reports an abort at the start. Keep the air conditioning off and the doors shut, since a load on the engine changes the idle speed the run relies on.

When the run will not complete

An adaptation that aborts at the same point every time usually means the unit cannot find a stable kiss point, and a pack with a glazed friction face will do exactly that. Read the entries in the mechatronic unit before the second attempt. A supply that sags during the run aborts it as well, so put a charger on the battery.

A car with a tired battery aborts the run late, after the tester has already spent time on it, and the abort reads like a gearbox fault. Measure the battery under load before you start and keep the charger connected through the whole procedure. If the run completes and the shake stays, the fault sits inside the pack.

Mechatronic pressure and the valve body

The unit applies the clutches with pressure from its own pump, and a valve body that leaks internally gives a take up that is slow and uneven. Read the clutch pressure during a take up on a road test and compare it with the value the tester expects at that torque. A pressure that lags the request points at the valve body.

Measure the feed at the mechatronic connector with the plug fitted and a scope on the wire, since a unit that resets during engagement drops its learned values and starts again from the base map. Check the ground strap between the gearbox and the body on the millivolt range while the starter turns, because that drop disturbs the unit in the same way.

What confirms the pack

The pack is the fault when the run completes, both values sit at the wear limit and the shake stays, with a clean engine side and no entries in the unit. The gearbox then comes out and the pack is measured. A pack that measures inside its thickness and still shakes has a mechatronic fault underneath it. Measure the friction faces with a micrometer at several points, because a worn face is rarely even across its width.

Write the adaptation values from before and after the run on the sheet, because that pair of numbers is the evidence for the repair. A fresh pack needs its own run before it takes up smoothly, so the adaptation is repeated after the rebuild. Let the car cool and drive it from cold before it goes back.

Rule the engine out with a smooth running test under load, then read both clutch values before you run anything at all. Bring the gearbox to temperature, keep a charger on the battery and let the adaptation finish. A run that completes and leaves the shake behind has pointed at the pack, and the measured thickness settles it. Road test the car again the next morning from cold and read the values once more.

What is measured on a DQ200 that shudders on take up
SymptomLikely causeWhat is measured
Shake in first and reverse, worse when hotKiss point has driftedAdaptation values for both clutches in the measuring blocks
Shake with the car loaded in a high gearEngine misfireSmooth running counters under load on a road test
Adaptation aborts at the same pointSupply falling or a glazed packBattery under load, entries in the mechatronic unit
Take up slow and unevenValve body pressure lossClutch pressure against the request during take up

Frequently Asked Questions

Can the adaptation be run with a cold gearbox?

The run is refused outside the temperature window, so the car is driven or idled until the oil reaches it. A run started cold aborts and stores nothing.

Does a replacement mechatronic unit need a run?

A new unit arrives with base values and no kiss point for the pack in that car. The run is made once the unit is coded and the gearbox is at temperature.

Will adaptation cure a worn clutch?

The run moves the kiss point to where the pack now takes up, and it cannot add friction material. A value at the wear limit means the pack comes out for measurement.

How is the car driven after the run?

The car is driven from cold with light throttle for the first few pulls, then checked again when hot. A shake that returns when hot is read from the values afresh.

Related Services