A BMW diesel that cranks well and never fires usually has either a signal missing at the engine unit or a unit that has lost its data. The EDC16 lives in the engine bay where water collects, and it holds the adjustment values for the injectors that are fitted to the car. Read the unit and the signals before anything is replaced.
The starter turns the engine at a normal speed and nothing catches, and there is no smell of fuel at the tailpipe. The glow lamp may work as usual, so the driver believes the fault is elsewhere. Note whether the engine ran and stopped, since a car that cut out while driving has a different set of causes from one that never started. Listen at the oil filler cap while an assistant cranks, because an engine with even compression sounds regular and one with a broken chain does not.
Ask about recent work on the injectors and about a flat battery or a jump start, because both put the unit in the frame. Ask whether the car was parked facing downhill in heavy rain, since water reaches the unit through the cover on these cars and the pins corrode from the outside in.
Connect the tester and see whether the engine unit answers at all. A unit that answers and stores no start related entries sends you to the crank signal and to the fuel side. A unit that does not answer sends you to its feeds and to the connector before anything else is measured. Read the rail pressure actual value at the same time, since a unit that answers and reports no pressure has told you the fault is on the fuel side.
Save the identification page and the coding, then read the injector adjustment values that the unit holds. Those values are written for the injectors that are fitted, and a set that does not match the hardware gives a car that cranks and will not fire. Photograph the page, because it is compared with the numbers on the injectors.
Each injector carries an adjustment code on its body, and the unit uses that code to trim the fuel it delivers. A unit with the wrong codes, or with a memory that has lost them, delivers fuel at the wrong moment and the engine will not run. Read the codes from the unit and compare them with the injectors one by one. Some of them are read with a mirror and a torch, and a photograph of each one saves a second look under the bonnet.
Check the numbers on the injectors themselves with a torch and a cloth, because a code read from a dirty injector is often one digit out. Write both lists on the sheet side by side. A mismatch on one cylinder is corrected with a coding session, and a unit with no codes stored at all travels to the bench.
Measure the permanent feed and the ignition feed at the unit connector with the plug fitted, then load each one with a bulb and read again. A feed that holds battery voltage open and falls under a bulb leaves the unit resetting during a crank, and a reset unit does not fire the injectors. Look at the pins for a white deposit as well, since water that reached the plug leaves a mark that a dry connector does not have.
Measure the ground pins to the battery post on the millivolt range, then clean the stud and the engine earth strap and read them again. A drop above about fifty millivolts disturbs the injector drive and produces entries that name several cylinders at once. Write the loaded feed values and the ground drop on the sheet.
Put the scope on the crank sensor wires at the unit connector and crank the engine, then look for a clean wave with even teeth. A signal with missing teeth or a flat section stops the unit from synchronising and the engine never fires. Compare the shape with the cam signal at the same moment. Crank for several seconds with the injectors unplugged if the engine floods, because a long crank gives the scope a stable pattern to read.
Check the sensor gap and the condition of the trigger wheel while the scope is connected, since a wheel with a crack or with rust in one tooth gives a signal that looks almost right. A signal that is present and even at both sensors sends you back to the fuel side and to the codes.
With the ignition off, measure the resistance of each injector at the harness connector and compare the values with each other. One that reads far from the others has a winding that has failed, and one that reads open has a broken wire in the harness or in the injector itself. Write the four values on the sheet. Repeat the readings with the engine hot, because a winding that is failing changes with temperature and a cold engine hides it.
Look at the injector plugs for oil and for cracked bodies, because the plugs sit in a hot place and the plastic fails with age. A plug that is not latched gives a car that starts and runs on some cylinders, which is a different complaint from a car that never fires at all.
The unit is the fault when it does not answer with good feeds and a good ground, or when it answers with no injector codes and a memory that cannot be written. Those results put the work on the bench. Write every value down, since the repair is planned from that sheet.
A unit that answers and holds the codes, and that sees both signals, is working, and the fault is on the fuel side. Check the rail pressure while cranking before the unit is condemned, because a rail that never builds pressure gives a car that cranks and never fires with a perfectly healthy engine unit.
After the repair or after new injectors, write the codes for each cylinder in the order the tester asks for them, then read them back from the unit. A code written into the wrong cylinder runs rough and stores a misfire entry on the first drive. Compare the read back values with the injector bodies before the engine is started.
Start the engine and let it idle until the fan cycles, then read the correction values for each cylinder and the fault memory. Write the coding result and the idle values on the sheet. A car that starts and idles evenly after that session is finished, and the customer gets the key with the codes already matched.
Check the rail pressure while cranking before you order a unit, because a diesel with a healthy DDE and no rail pressure behaves exactly like a car with a dead unit. Then read the injector codes from the unit and compare them with the numbers on the injectors, since a set that does not match stops the engine from firing and it is corrected with a coding session. Write the loaded feed values down as well, because a unit that resets during a crank never fires an injector and the meter shows it in seconds.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Cranks evenly, never fires | Injector codes do not match | Codes read from the unit against the injectors |
| No answer from the unit | Feeds or ground at the plug | Loaded feeds and millivolt ground drop |
| Unit resets during a crank | Feed falls under load | Feed at the plug with a bulb on it |
| Entry names one cylinder | Injector or its harness | Resistance at each injector plug |
It will not fire on a push start, because the unit drives the injectors and there is no mechanical pump to take over. The car is brought in and the feeds are measured first.
The adjustment codes in the unit still belong to the old injectors. The codes are written for each cylinder and read back before the engine is started.
The pins and the board show corrosion and a white deposit, and the cover has a mark where water stood. A unit with corrosion is opened and the board is inspected before it is powered again.
The coding and the injector codes are written back and read from the unit afterwards. The identification page is photographed first so the same data goes in.