PGE Tuning Lab

Audi A4 B7 comfort module with dead locking and windows

The remote does nothing, no door locks on the switch, and every window is dead at once. That combination on the A4 B7 points at one unit, since the comfort module drives all of it from the rear quarter. The order below proves whether the module is offline or whether it is alive and refusing to work.

What fails at once

The customer reports a car that will not lock on the remote and will not lock on the door switch either, with the windows dead on all four doors at the same time. The interior lights may be out as well, and the boot may only open with the key in the lock. Ask which of those still works, because a single working function tells you the module is powered and only part of it has failed. That one answer decides whether the job is a supply or a board.

Ask whether the fault arrived after rain or after the boot was loaded in wet weather, since water in the rear quarter is the usual cause on this car. Ask too whether the battery has been flat recently, because a module that has been undervolted can lose its coding and then refuse the remote. Write both answers down before you open the trim, and photograph the well as you go in.

Where the module sits

The comfort module is in the rear left of the luggage compartment behind the side trim, where it is easy to reach and easy to soak with water from above. It controls the locking motors and the window motors, and it drives the interior lighting from the same board. The aerial for the remote is wired to it on this platform, which is why a dead remote and dead locks arrive together.

Look at the trim for a water stain before you remove it, since a stain above the module tells you the whole story in a second and saves an hour of measuring. A module sitting in a damp well will fail again after every repair until the leak behind it is closed. Photograph the well and the connectors before anything is unplugged, so the loom goes back the way it came out. Note the part number and the coding before the unit leaves the car.

Does the module answer

Open the comfort address in the diagnostic session and see whether the unit answers at all. A unit that answers and stores entries about the locking motors is alive, and the job moves to the outputs and to the coding. A unit that does not answer has a supply or a bus fault in front of it, and the measurements below find which. Write the identification screen down while it is up.

A unit that answers on one attempt and not on the next has an intermittent supply, and the connector is the first suspect on a car of this age. Wiggle the plug while the tester is connected and watch the identification screen for a dropout. A unit that drops out as the plug is moved has a terminal tension problem that no replacement will cure.

Supply and ground

Measure the permanent feed at the module connector with the plug fitted and fine probes through the seal, then measure the ignition feed in the same way. Both should sit at battery level and neither should move when a window is commanded. A feed that collapses under that load points at the fuse contact or at the supply stud. Measure across the fuse blades while the load is on.

Measure the ground pins against the battery post on the millivolt range while a window motor runs. A drop above fifty millivolts disturbs the module and makes the motors slow, and it reads like a module that is failing on a road test. Clean the stud and repeat the reading. Look at the board only after that.

Water and the rear quarter

Pull the connectors and look at the pins under a lamp. A green pin has been wet and a pin that has gone black has been hot, and the two faults need different repairs. Clean a pin only to prove the circuit, because a pin that has corroded once will corrode again through the next winter. Replace the terminal where the crimp tool reaches it, then seal the joint.

Check the rear lamp seal and the boot vent behind the trim, since both let water into that well on a car of this age. Run water over the rear of the car with the trim off and watch where it lands, then repeat the test with the boot shut. A repair that leaves the water path open will bring the same fault back and the customer will not accept it twice.

The comfort bus

Scope the two comfort bus wires at the module connector with the ignition on and look at the levels and at the frames on the screen. A wire held at a fixed level has lost its pair, and the module then reports faults from every door at once. Check the loom where it passes the rear seat for a rub against the frame.

Measure the resistance between the two bus wires with the battery disconnected and compare it with the figure the diagram gives. A reading far from that figure points at a broken wire or at a module holding the bus down. Unplug the door modules one at a time and watch the reading come back, since the one that changes it is the one at fault. Write the reading down at each step so the pattern is visible.

The remote and the door switches

Try the second key and watch the central locking values while the buttons are pressed. A value that changes with the second key proves the receiver and the module and leaves the first key as the fault. A value that never changes sends you to the aerial and to the receiver inside the module.

Read the door switch values one door at a time while each is opened and closed by hand. A door that never reports open leaves the module waiting and refusing to lock the car, which looks like a module fault on the road. That fault is settled in five minutes with the tester and a hand on each door in turn. Write the values on the sheet for all four doors.

What confirms the module

The module is the fault when it answers on the tester, the feeds and grounds hold under load, the bus is alive and the outputs stay dead with the switches reporting correctly. Those results together leave the board, and the unit is repaired with its coding saved first. A board with water damage across several layers is replaced instead of repaired.

Write the coding and the adaptation values on the sheet before the module leaves the car, because a replacement arrives blank and the car will not lock until it is written. Then work every lock and every window twice before the trim goes back on. Check the well for water after the first rain and bring the car back in if it is damp.

See whether the unit answers before you measure anything, because a module that talks has a different job in front of it. Measure the feeds with the plug fitted and the grounds on the millivolt range while a motor runs. Water in the rear quarter explains most of these arrivals, and the leak is closed before the new unit goes in.

What is measured when locking and windows fail together on an A4 B7
SymptomLikely causeWhat is measured
No locking and no windows at allModule offlineIdentification screen in the comfort address
Works once, then dead againTerminal tension at the plugIdentification while the plug is moved
Fault after rainWater in the rear quarterTrim stain, pins under a lamp, water test at the rear
Every door reports a faultComfort bus held downScope of both wires, resistance with the battery off

Frequently Asked Questions

Can the windows be opened with the key when the module is dead?

The convenience function runs through the same unit, so a dead module takes that with it. A car that still opens on the key has a partly working module.

Is a used comfort module a straight swap?

A used unit carries the coding of the car it came from, so the coding is read from the old one and written to the new. The remote is matched afterwards.

Why does the remote stop working as well?

The receiver sits in the module and the aerial is wired to it, so the same fault takes the locking and the remote together. The second key proves which side has failed.

What is checked after the repair?

Every lock is worked twice, every window is run to its stop, and the rear quarter is checked for water after the first rain. A damp well means the leak was not closed.

Related Services