A CDI that runs rough after an injector has been replaced on a W203 or a W211 usually has one of two things behind it, and both are settled with the tester before the spanner comes out. Either the code on the new injector has not reached the control unit, or the injector in that hole is leaking past its seat. The measurements below separate those two on the same visit.
The complaint is a shake at idle that the driver feels through the seat, and a puff of grey smoke at a cold start. Some report a knock from one side of the engine when it is cold. Ask whether the shake began the same day the injector was changed, because that answer points straight at the coding rather than at wear.
Write down which cylinder was worked on and who did the job. A car that has had an injector fitted without the code written will idle badly on a unit that is otherwise healthy. Ask about hard starting when warm and about fuel in the oil, since a leaking injector shows in both places and the second one is the expensive one. Check the invoice for a part number, because a used injector from another engine carries a code this car was never built around.
The injector carries a code etched on its body, and that value is stored in the CDI unit for each hole. Read the stored values with the tester on the coding page and compare them one by one with the numbers on the injectors in the car. A hole where the stored value belongs to the old injector is the fault, and the shake will sit on that cylinder.
Write the numbers on the sheet as you read them, including the ones that match. A unit that has no value at all in one position has been coded after a replacement and the job was left half done. Do not clear the coding page or reload a full data set before the numbers are recorded, because those values cannot be recovered from the car.
With the engine idling at temperature, open the smooth running page and read the correction value for each cylinder in milligrams per stroke. The cylinder that the unit is feeding hardest is the one that is not delivering. Read the page at idle and again at fifteen hundred revs, because a correction that evens out with revs belongs to a fault at low delivery. Write each correction opposite its cylinder on the sheet.
Compare that page with the coding page before you condemn anything. A cylinder with a large correction and a stored code that belongs to the old injector is a coding fault. A cylinder with a large correction and a correct code has a delivery problem in that injector or a compression problem above it, and the next test decides which.
Connect a graduated vial to the leak off pipe of each injector and crank the engine for a fixed count, then compare the volumes side by side. A vial that fills far beyond its neighbours has an injector passing fuel past its internals, and that cylinder runs lean at idle while the rail loses pressure. Repeat the test with the engine idling if it starts.
Read the volumes at the same engine temperature on every test, since cold oil changes the result and a comparison across temperatures tells you nothing. A set where one vial is clearly ahead is a leaking injector. A set where all vials are high points at the high pressure pump or at a return line that is restricted, and the injectors stay in.
Read the actual rail pressure against the specified value at idle with the tester, then watch both during a snap of the throttle. A rail that sits below its target at idle and recovers with revs has a leak on the high pressure side. A rail that overshoots and hunts points at the quantity control valve on the pump.
Measure the pressure sensor supply at its plug and compare the voltage with the pressure on screen. A sensor that reports a value the engine cannot be running at sends the unit into a correction that no injector can satisfy. Rule that out before the injectors are touched, because a sensor is cheaper than a set of injectors. Repeat the reading at two thousand revs, since a sensor that drifts hot looks clean just after a start.
Measure the winding of each injector with a milliohm meter and compare across the set. A winding far above or below its neighbours has a fault inside the injector, and its cylinder will misfire hot. Check the plug for a pushed back terminal and for diesel in the shell, since a leak at the seat sends fuel up the harness.
Measure the injector loom from the unit plug to each injector with both ends free, then flex the branch while the meter is connected. A reading that steps as the loom moves is a broken strand and it gives a fault that comes and goes with engine movement. Write each value against its cylinder, since the comparison is what carries the diagnosis.
If the code is correct and the leak off test is clean, the unit itself is tested on the bench with the injector drivers loaded. A driver that fires weakly shows as a short pulse at the plug and a cylinder that never balances. A driver that is shorted holds its injector on and floods that hole at idle.
Keep the bench result with the coding values on the same sheet, because a car that comes back with the same shake is judged against both. A repaired unit fitted with the codes already written saves a second visit, and the smooth running values after that fit are the proof that the repair held.
Write the injector codes with the tester, one hole at a time, and confirm each entry on the screen before you move on. Then clear the adaptations, start the engine and let it idle until the fan cycles once. Read the smooth running page again after that idle, since a set of values that has settled close together is the sign the coding took.
Take the car on a road test with a long climb and read the values once more when it is hot. Check the fuel filter housing for metal and the oil for a diesel smell before the keys go back, because a leaking injector that was coded rather than replaced returns within a week. Write the rail pressure and the correction values on the sheet.
Judge the idle with the bonnet closed and the car on the ground, since a shake that disappears with the bonnet up belongs to a cover or a pipe rather than to the fuel system. Then listen at the oil filler with a hand over it and feel for a pulse that matches the shake, because crankcase pressure from one worn bore copies a bad injector almost exactly.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Shake began the day of the swap | Injector code not written | Stored codes compared with the numbers on the injectors |
| Rough idle, hard warm start | Injector leaking past its seat | Leak off volume per injector at one temperature |
| Grey smoke and a knock when cold | Worn nozzle or low compression | Smooth running values, then a compression check |
| Rail pressure below target at idle | Quantity valve or a leak | Actual against specified pressure, sensor supply voltage |
It starts and moves, but the idle stays rough and the unit keeps a correction on that hole. The code is written before the car is handed back, and the values are read again afterwards.
The unit is still fuelling for the injector it was coded with. A new nozzle delivers a different quantity, so the correction is wrong until the code on the body reaches the control unit.
The leak off volume is measured into graduated vials and compared across the set at one temperature. The injector that fills well ahead of the others is passing fuel past its internals.
The smooth running values and a compression check come next. A driver stage in the unit or a worn bore copies the symptom, and both are measured before any injector is replaced.