PGE Tuning Lab

Audi BCM2 faults on the A4 B8

An A4 B8 that unlocks and then refuses to start, with a message about the key, usually leads to the BCM2, because that unit holds the immobiliser data for the car. A unit taken from another car brings component protection with it, and the car refuses to start even with a good key in the reader. The second key test comes before anything is opened.

The car does not see the key

The owner says the car unlocks on the remote and the dash lights up, and the engine does not turn over or turns over and stops at once. Sometimes a message about the key appears and sometimes the dash stays quiet, which makes the fault look random. Ask what happened before it started, because a flat battery and a workshop visit lead to different answers.

Ask whether a second key was tried and whether the fault appeared after a unit was replaced. Those two answers separate a key problem from an immobiliser problem in one step. A car that worked with one key and stopped after a jump start is a different case from a car that never accepted the key at all. Write the answers on the job card, because the rest of the diagnosis depends on them and the owner will tell the story differently next week.

The second key and its battery

Put the second key in the reader and try to start the car before you open any panel. A different result from that key separates a worn transponder from a unit fault, and it saves an unnecessary repair on a unit that was working all along. Note which key gives which result on the sheet.

Then check the remote battery, because a key with a flat cell still starts the car when it is held against the reader but not when it is left in a pocket. Open the key, measure the cell and fit a new one before the next test. A key that starts the car after a new cell is a key that was never at fault. Measure the cell under load rather than at rest, since a cell that reads well over three volts can fall away the moment the remote transmits.

Immobiliser live values at the BCM2

Open the access and start authorisation address and read the live values with the key in the reader. The unit should report a key present and a key that is authorised, and those two values together tell you whether the reader or the data is the problem. Write both down before you clear anything.

A unit that reports no key with a known good key in the reader points at the reader coil or at its wiring. A unit that reports a key present and not authorised has the key data itself to blame, and the key list is read next. The two cases are repaired in completely different places on the car. Take both readings with the key held still in the reader, because a hand that moves the key during the read gives a value that looks like a failing coil.

Component protection after a swap

A used BCM2 carries the data of the car it came from, and the car it is fitted to refuses to work until the unit is matched and the protection is lifted. The tester reports component protection as active, and the engine will not run while that message is in the unit. Read the message before you look for a wiring fault.

Matching the unit needs the car connected to the manufacturer system with a stable supply on the battery, because the process writes to the unit and a supply that falls away in the middle leaves it half written. Keep a charger on the car for the whole procedure and write down the result of each step. A unit that was half written reports component protection again after the next key cycle, and the procedure is then repeated from the start rather than resumed.

Supply and the reader for the key

Measure the feed at the BCM2 connector with the ignition on and the plug fitted, using fine probes through the seal. A feed that sits below battery level makes the reader weak and the key detection unreliable. Then measure the ground pin against the battery post on the millivolt range.

Measure the resistance of the reader coil at its plug with the unit disconnected. A coil that reads open has a broken winding, and a coil that reads far from the value on a known good car has a shorted turn. Both faults give the same complaint and both are found with one meter reading. Flex the coil lead while the meter is connected and watch the reading, because a value that jumps as the lead moves is the fault you are hunting for.

Reading and writing the key data

Read the key list from the unit and compare the entries with the keys the owner has brought. A key that was never written appears exactly like a key that has failed, so the list is the place where the two are separated. Write the number of keys stored on the sheet. Ask whether a key was ever lost or replaced, because a list with a missing entry explains a car that starts on one key and refuses another with no fault present at all.

Save the data before any write, because a write that goes wrong erases the list and leaves the car with no keys at all. After a write, test each key in turn with the car locked and unlocked between them, and note which keys are accepted. A key that is accepted once and refused the second time points at a reader that is failing.

What the tester will not tell you

The tester reports what the unit believes, and it cannot tell you whether a coil is weak or whether a key has been dropped once too often. Those answers come from a meter and from a second key. Treat a stored immobiliser entry as a starting point rather than as a diagnosis.

The tester also cannot see a key that is present but badly read, because a partial read still reports a key present. That is why the reader coil is measured even when the live value looks correct. A coil with a shorted turn reads a key at two centimetres and misses it at five.

What confirms the fault

The BCM2 is the fault when the supplies hold under load, the ground drop is low, the reader coil measures correctly, the second key behaves the same way, and the unit reports a key present that it will not authorise. Those results together leave the data or the board as the repair.

Component protection is a separate finding, and it is confirmed by the message the unit stores rather than by a measurement. A car that was matched correctly and still refuses to start has a key that no longer matches the list, and the list is read again before the unit is opened.

Save the key data before the first intervention, because the list of keys lives in the unit and a careless write leaves the car with none. Photograph the part number and the coding index, then read the authorisation values with the second key in the reader. Note which key the car accepts and which it refuses. A unit that answers on the bench and refuses a known good key in the car usually has a reader coil that is failing, and that coil is measured before the board is touched.

What is measured on an A4 B8 whose BCM2 will not accept the key
SymptomLikely causeWhat is measured
No key reported with a good key fittedReader coil or its wiringCoil resistance at its plug, unit unplugged
Key present but not authorisedKey data no longer matchesKey list read from the unit
Component protection activeUnit taken from another carMessage stored in the unit after a swap
One key works, other refusedKey never written or worn outResult of each key with the car cycled between them

Frequently Asked Questions

Why does the car unlock but refuse to start?

The remote and the immobiliser are separate paths inside the same unit, so a car can open on a key that the unit will not authorise. The authorisation values decide the start.

Can the unit be matched without the manufacturer system?

The matching and the lifting of component protection are written by the manufacturer system with the car online. A stable supply is kept on the battery for the whole procedure.

Does a flat battery cause this fault?

A battery that falls away during a write leaves the unit half written, and the key list can be lost that way. The list is read first, then the supply is measured before any write is repeated.

What is checked after a unit is matched?

Every key is tested in turn with the car locked and unlocked between them, and the reader coil is measured once more. A key that fails on the second attempt points at the coil.

Related Services