A Teana whose wipers fail on every speed, including the fast one, is not usually a tired motor. The body unit drives the wipers from an input the stalk sends, so a switch that reports nothing leaves the motor with no command at all. The input is read at the unit before the motor is touched.
The driver reports that the wipers stopped in the rain and that no position of the stalk brings them back, or that they move only when the stalk is held. The second pattern is the useful one, because a stalk that works when held is reaching the unit and the fault is somewhere else.
Ask whether the washers still work and whether the wipers park when the stalk is released, since a washer that sprays proves the unit is alive and a wiper that will not park points at the motor circuit rather than at the switch. A wiper that parks by itself after the stalk is released proves that circuit can finish a cycle.
The body unit takes the stalk input, decides the speed and drives the wiper relay, so the signal passes through two stages before the motor sees anything. A fault in either stage leaves the wipers dead while every other function of the unit works normally.
Read the body unit address and write the entries down, then look for an entry that names the wiper relay or the stalk input. An entry that names neither does not clear the unit, because a dead input often stores nothing at all.
The stalk does not send a simple on or off. It reports a position through a resistance ladder or a set of contacts, and the unit reads that value to choose between the intermittent position and the fast one. A stalk with a worn contact reports a position between two detents and the unit ignores it.
That is why the live value matters more than a continuity check at the plug, because continuity tells you a contact closes and not which position the unit believes it is in. Read the value in every stalk position and write the numbers down. Read it twice in each detent, because a contact that is going open gives two different numbers seconds apart.
Read the stalk input in the live values with the ignition on and step through every position from off to fast. Each position should give a distinct value and a value that repeats between two positions names the stalk rather than the unit. Hold each position for a moment, since the unit steadies the reading before it acts on it.
Then measure the input wire at the unit connector with the plug fitted, using fine probes, and compare the voltage in each position with what the live value reported. A wire that shows the same voltage in every position is a stalk or a clock spring fault.
A stalk that steps cleanly through its values and an input wire that follows it clears the switch, and the fault moves inside the unit or to the relay it drives. That order is what keeps a good stalk from being replaced on a guess. It also keeps the unit closed when the switch turns out to be the only fault.
A stalk that gives the same value in two positions is the fault, and the unit stays closed. Do the test twice, once with the steering wheel straight and once turned, because a clock spring with a broken track fails only at one angle.
The motor carries a park switch that tells the unit where the blades are, and a motor that never reports park leaves the unit unwilling to start a new cycle. That is why wipers sometimes run once and then stop in the middle of the screen.
Feed the motor directly from a fused supply to see whether it runs, and watch whether it returns to the park position when the feed is removed. A motor that runs and parks is healthy, and the search returns to the unit and to the relay.
Check the fuse that feeds the wiper circuit and measure the voltage on both sides of it with the ignition on, because a fuse that looks intact can carry a poor connection in its holder. A drop across the holder is a fault worth cleaning before anything else. Measure with the wipers switched on, because a holder that reads well at rest can drop under the motor current.
Measure the motor ground in millivolts against the battery negative post with the wipers running, since a ground that lifts under load stops the motor without blowing a fuse. Clean the point and repeat the measurement so the change is visible on the sheet.
Run the wipers through every position, including intermittent, and watch for a cycle that stops away from the park position. Then spray the screen and let them park on their own, because that final movement is what the driver will notice first in the rain.
Write the stalk values you read and the voltage at the motor plug on the sheet, so a return visit starts from the same numbers. Tell the owner whether the fault was the switch or the circuit, because that answer decides what is checked if the wipers stop again.
Separate the command from the execution before you touch the body control module. Read the stalk input in live data with the wiper switch in every position, then check the motor connector for supply and ground while the command is present. A module that receives the command and sends nothing to the motor is a real module fault, while a module that receives nothing is telling you the problem is in the switch, the clock spring or the wiring between them.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Dead on every speed | Stalk input missing at the unit | Stalk live value stepped through all positions |
| Works only while the stalk is held | Worn contact in the stalk | Input voltage at the unit plug in each position |
| Runs once and stops mid screen | Park switch not reporting | Motor fed directly and watched for park |
| Slows and stops under load | Ground lifting at the motor | Millivolt drop to the battery negative post |
Because the unit needs a position from the stalk before it drives the motor, and a dead input leaves the motor with no command. The stalk value is read in the live data before any panel is opened.
It means the input reaches the unit in at least one position and the motor circuit can run. The fault is then in the stalk positions that do not register, and the live values show which ones.
No, it only shows that a contact closes. The unit reads a position value, so the live data and the voltage on the input wire are what confirm the stalk.
A park switch that never reports the rest position leaves the unit unable to finish the cycle. The motor is fed directly to see whether it runs and parks on its own.