A Polo 6R that loses its brake lights and its indicators together looks like a failed body control unit, and the unit is rarely the cause. Both circuits share an earth at the rear and a supply that the module switches, so one joint or one switch can take them both out. The order below finds that joint before the module is condemned, and it costs a meter and ten minutes.
The report is usually a car behind flashing lights at a junction, or a warning that the indicators click but nothing lights outside. Some drivers notice the brake lights only when another car pulls alongside and honks. Ask whether the hazard lights still work, because a hazard function that lights every corner points away from the lamps and towards the switch path. Ask when the lamps last worked.
Ask whether the fault came on after work on the tailgate or after a tow bar was fitted. A pinched loom in the tailgate hinge and a wrong bulb in a holder both produce this complaint. Write the answer on the sheet with the mileage, since a recent repair is the first thing to check. Look at the lamps themselves before anything else.
Read every address and then open the body control unit on its own. Look for codes that name a lamp circuit or an open load, or one that names a short to earth. A code that names one side only sends you to that cluster, while a code that covers several lamps points at a shared earth or a shared supply. Clear the codes and read again after a key cycle.
Save the coding page before anything is changed. The unit is coded for the lamps fitted, and a car that has had a bulb monitor setting changed will report faults on lamps that are working. Write the coding string on the sheet, because a replacement is prepared from it and it cannot be recovered later. Photograph the page as well.
Check the fuses for the indicator circuit and the brake circuit by hand rather than by eye, and confirm each one with a meter on both blades while it is loaded. Then go to the rear clusters and measure from the earth pin of each lamp holder to the battery negative post with the lamps on. A reading above a few tenths of a volt is your fault. Read both clusters in the same minute.
Clean the earth point on the body behind the trim and repeat the measurement on the same pins. Both clusters often earth at one stud, and a stud that has corroded takes the brake lights and the indicators out at once. Refit the nut with a star washer and read again with the brake pedal held down. The load is what moves a weak joint.
The switch on the pedal sends a signal to the unit, and the unit decides when the lamps light. Read the switch status on the live page while an assistant presses the pedal. A status that never changes while the pedal moves sends you to the switch and its adjustment rather than to the lamps.
Measure the switch contacts with a meter at the plug, then press the pedal by hand and watch the reading change. A contact that stays open has failed, and one that stays closed holds the lamps on and drains the battery. Check the plunger travel against the pedal arm, because a switch that is not seated gives the same result as a dead one. Write the travel down.
With the pedal held and the hazard switch on, back probe the output pins at the unit plug and read each one against a known good circuit. A pin that shows battery level with no lamp connected and drops to nothing with a bulb fitted has a driver that cannot carry current. That is the measurement that condemns a channel.
Use a bulb of the correct wattage for the test rather than a meter alone, since a high impedance meter reads a voltage through a failed output. Compare the left and the right channel on the same pin row, and write both numbers down. A channel that is far below its pair has failed inside the unit. Take the unloaded figure first and the loaded figure under it.
The hazard switch feeds the indicator request to the unit on the Polo, so a switch that has failed stops the indicators while the brake lights stay alive. Read the switch status on the live page and press it several times. A status that flickers or that never arrives names the switch or its wiring.
Measure the switch plug for a supply and a ground, then bridge the signal pin briefly and watch the lamps. A circuit that lights on the bridge proves the switch. Wiggle the plug while the hazard function is on, because these switches sit in the centre of the dash and they take heat. Keep the bridge to a second, since a long one heats the circuit.
On the bench the unit is fed at thirteen and a half volts and each lamp output is loaded with a bulb of the right wattage while the function is commanded from the tester. A channel that holds its voltage under that load is healthy. One that collapses has a failed driver on the board. Run every lamp function in turn.
Watch the current per channel at the same time. A channel that pulls far more than its pair has a short on the board or a lamp circuit that is still faulty in the car. Keep the unit powered for several minutes after the test, since a driver that fails when warm passes a cold bench run and returns the complaint. Note the warm figure too.
Fit the unit and connect the battery, then read the coding page before the first test. Then check the brake lights with the pedal, the indicators on both sides and the hazard function, and watch the lamps with the engine running as well as off. A circuit that works with the engine off and fails when it runs has a supply problem. Read the lamp monitor page as well.
Write the earth readings on the sheet, with the switch status and the loaded output figures. That record is what makes the second visit short, and it also shows whether the fault moved. Ask the driver to check the lamps from outside before the car leaves, since a lamp that is out on one corner is easy to miss in a workshop. Keep the earth figure at the top.
Carry out the final check in the dark with the rear of the car against a wall, since a lamp that is dim rather than dead shows up in a reflection and nowhere else. Press the pedal slowly and watch for a delay, because a switch that is out of adjustment lights late and the driver never mentions it. Write the result on the sheet with the earth figures, and note whether the lamps answer on the first press or the second.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Both circuits dead together | Shared earth at the rear clusters | Volts from the lamp earth pin to the battery post |
| Indicators click, no lamps | Hazard switch signal | Switch status on the live page, then a bridge at the plug |
| Brake lights never light | Pedal switch or its seating | Contact change at the plug while the pedal is pressed |
| One channel weak under load | Output driver inside the unit | Output pin with a bulb fitted, against its pair |
It is not roadworthy, and a car behind cannot read the intention. The earth and the pedal switch are measured first, because both are quick and both explain the whole complaint.
Both circuits switch through the body unit and both use the earth at the rear clusters. One corroded stud takes them out together, and the millivolt reading names it.
Fit a bulb of the correct wattage and read the pin again. An output that collapses under that load has a failed driver, while a meter alone reads a voltage through a broken path.
Yes. The coding string is read before the old unit is removed and written into the replacement, then the lamps are checked on both sides.