PGE Tuning Lab

Audi air suspension level control module on A6 C6 and Q7

An A6 C6 or a Q7 that sits down at one corner, or that runs its compressor without rising, shows a level control message and stores a fault in the module that runs the system. The module reads four height sensors and it drives a compressor and a valve block, so the fault can sit in any of those places. The order below keeps the module in its place until the sensors have spoken.

The complaint and how the car sits

The owner reports a message on the dash or a car that leans to one side in the morning. Some report that the car rises and then sinks again within an hour of being parked. Ask which corner is low, because one corner points at a spring or a valve, and a whole axle points at a shared line.

Ask whether the fault came on after work underneath the car or after a tyre change. A height sensor linkage that was bent during a jacking job gives a level fault that looks electrical. Write those answers on the sheet with the mileage, since the history decides whether you start at the sensor or at the spring.

The level values before anything is jacked

Read the measured height at each corner on the live page with the car on its wheels and the engine running. Write the four numbers down. A corner that reads far from the others, with the car sitting level, sends you to that sensor and its linkage. A corner that reads correctly while the car leans sends you to the spring. Read the four values twice, ten minutes apart.

Read the same four values again after the car has settled for ten minutes with the ignition off and on again. A value that drifts while the car is parked is a leak, and the sensor is reporting it honestly. That single comparison saves a great deal of work on the module, which is usually the last part at fault.

Supply and ground at the module

The module sits behind the trim in the boot area on both cars, where water from a blocked drain finds it. Measure the permanent feed and the ignition feed at its plug with the ignition on, then load the permanent pin with a bulb and read again. A feed that collapses under the bulb explains a module that resets while the compressor runs.

Put the meter on millivolts and read from the ground pins to the battery negative post. A drop above a tenth of a volt is too much for a unit that drives a compressor. Look at the pins in the plug for green corrosion and at the case for water marks, because a unit that has been wet gives faults that move from day to day.

The height sensors and their voltages

Each sensor is a potentiometer with a supply and a ground, and a signal that moves through its range as the arm swings. Measure the signal at the plug while the car is raised on a jack under that corner, and watch the voltage change smoothly. A signal that steps, or that sits at one rail, is a sensor or a linkage.

Compare the signal on the low corner with the same corner on a car that sits level, since the absolute figure matters less than the change across the travel. Check the arm and the ball joint at each end, because a link that has popped off leaves the sensor reporting a height the car is not at. Write each voltage down as you measure it.

The compressor and the current it draws

Command the compressor from the tester and read the current with a clamp on its feed. A compressor that pulls a heavy current and does not raise the car has a seized or worn pump. One that pulls almost nothing has an open winding or a relay that is not closing. Read the pressure at the valve block at the same time.

Listen to the compressor while it runs and watch the current for the first ten seconds. A pump that starts low and climbs as it heats is on its way out, and it will fail on a cold morning. Check the relay contacts for pitting and the fuse holder for heat marks, since a relay that chatters gives a fault that comes and goes. Note the current at the ten second mark.

The valve block and the air springs

The valve block holds a solenoid for each corner, and a valve that sticks holds a corner down or lets it rise when it should not. Measure each solenoid winding and compare the set, then command each valve in turn from the tester and watch the height at that corner. A corner that does not move while its valve is commanded names the valve or its line. Write each winding value opposite its corner.

Spray soapy water on the spring and on every union while the car is at normal height, and look for bubbles at the fold of the spring. A spring that leaks at the fold sinks overnight and rises when the compressor runs. Check the line at the strut for a chafe, since a rubbed line gives the same pattern and it is easy to miss.

What the bench proves about the module

On the bench the module is powered at thirteen and a half volts and each output is loaded with a test lamp or a solenoid of the right resistance while the function is commanded. An output that holds its voltage under that load is healthy. One that collapses has a driver that cannot carry the current of a valve.

Read the module with the height signals simulated on the bench, because a unit that has lost its sensor reference will not drive anything. A unit that runs the compressor output but reads no height has a fault on its input side, and that is a different repair from a driver. Keep it powered for several minutes, since these units fail when warm. Note the current it draws while driving a valve.

Refitting and the calibration

Fit the module and connect the battery, then read the level values before a calibration is attempted. Then run the calibration by the book with the car on level ground, the fuel tank at the stated level and nobody in the car. A calibration done on a slope writes offsets that the car carries from then on, and the fault returns.

Write the four height values before and after the calibration on the sheet, with the compressor current and the pressure at the block. Those numbers are what the next visit is compared against. Check the car after an hour parked, since a spring that leaks slowly shows only after the system has had time to settle.

Leave the car overnight and look at it before the ignition is switched on, because a system that leaks down shows in the morning and nowhere else. Measure the height at each corner with a tape from the ground to the arch, then compare it with the numbers from the visit. A corner that has lost height while the others held tells you the leak is on that corner. Write the tape readings beside the tester values.

What is measured on an A6 C6 or Q7 with a level control fault
SymptomLikely causeWhat is measured
One corner low in the morningLeaking spring or lineSoapy water at the fold and at every union
Car sits level, message on the dashHeight sensor or linkageSignal voltage at each sensor through the travel
Compressor runs, car does not riseWorn pump or stuck valveCompressor current and pressure at the block
Fault returns after a repairCalibration done on a slopeFour height values before and after calibration

Frequently Asked Questions

Can the car be driven with a level fault?

At normal height it can be driven with care, but a car sitting on its bump stops is left standing. The height at each corner is read first so the decision is made on a measurement.

Why does the fault come back after the module is replaced?

The calibration was not run, or it was run with the car on uneven ground. The four height values are written down before and after so that offsets are visible.

How is a leaking spring found?

Soapy water on the spring and on the unions while the car is at normal height. Bubbles at the fold of the spring or at a rubbed line name the corner.

What proves the module is at fault?

The supply and the height signals are read first, and the bench decides the rest. An output that collapses under a load on the bench has failed, while a unit that drives every output correctly is not the part at fault.

Related Services