PGE Tuning Lab

Audi adaptive headlight fault on A8 and Q7

An A8 or a Q7 with the adaptive light warning usually has a level sensor that has stopped reporting, and the headlights then park themselves in a safe position. The range control module reads both axles and it drives a motor in each headlight. Read the sensor values while the car is loaded before you look at the lamps.

The adaptive light warning

The cluster shows a message about the headlights and the beams sit low, or they stop following the steering wheel on a bend. The driver often says the lights were fine until the car was loaded for a trip. Note whether the warning appears at key on and stays, since a warning that clears after a few seconds points at a sensor that is slow to wake. A warning that appears only with the boot full points at a sensor near the end of its travel.

Ask about recent suspension work and about a battery that went flat, because both leave a module with a stored entry and a beam pattern that never returns to its setting. Ask as well whether the car has been on a lift, since a sensor arm that was moved during the work sets the warning on the first drive.

Codes and the module address

Read the range control address and save the memory, then note which sensor or which motor is named. An entry for one axle sensor sends you under the car at that corner, and an entry for one headlight motor sends you to the lamp on that side. Write the entries out in the order they were stored.

Read the identification page and photograph the label, because the module is coded to the car and a replacement is prepared from that page. A module fitted without the coding sets the warning again on the first key cycle and the beam pattern stays low.

The level sensors at the axles

Read both sensor values on the data page with the car on its wheels and the ignition on. Each should sit in the middle of its range and neither should be at the end of it. A value pinned at one end points at a sensor arm that is bent or at a link that has come off its ball. Note the value with the car empty and again with two people in the back, because a sensor with a worn track reads correctly in one state and drifts in the other.

Load the boot and watch both values move, then unload and watch them come back. A sensor that does not move has a broken arm or a dead element, and one that moves in steps has a worn track inside it. Compare the two axles with each other, since one that reads far from the other on a level car names the part.

The reference voltage and the signal

Measure the reference voltage at the sensor connector with the plug fitted, using a fine probe through the seal. It should read about five volts and it should hold with the sensor connected. A reference that sits low with the plug on has a sensor that is pulling it down, and the module then reports both axles as faulty. Unplug the sensor and read the reference again, since a value that returns to five volts with the plug off proves that the sensor is the part pulling it down.

Back probe the signal wire and watch it while an assistant pushes the body down at that corner. The value should change smoothly through its range. A signal that jumps or stays flat while the body moves is a sensor fault, and the module is working correctly to report it.

The motors in the headlights

Run the basic setting with the tester and listen at each headlight, because the motor should move the reflector through its travel and back. A lamp that is silent has a motor that is not being driven or a motor that has failed. Watch the beam against a wall so the movement is visible as well as audible. Take each side in turn, because a motor that moves a little and stops looks like a working motor from the driver seat.

Measure the drive at the motor connector while the basic setting runs, using the scope on the two motor wires. A drive that appears at the connector and no movement in the lamp names the motor, and a lamp that moves with a good drive has proved the motor and its wiring. Write the result for each side.

Supply and ground at the module

Measure the permanent feed and the ignition feed at the module connector with the plug fitted, then load each one with a bulb. A module that sees a feed which sags during a start sets entries of its own, and those entries read like sensor faults to a reader who does not check the value. Look at the sensor arms for a stone strike as well, since a bent arm on a car that has been on a rough road sets the same warning.

Measure the ground pins to the battery post on the millivolt range, then clean the stud and repeat the reading. A drop above about fifty millivolts upsets the sensor reference and the module reports values that make no sense at either axle. Check the module for water, because it sits where a leaking screen drains.

Basic setting after a repair

After a sensor, a motor or the module is replaced, run the basic setting with the car on level ground and the tyres at the right pressure. The module learns the range of each sensor and it stores the position it needs for the beam pattern. Skip that step and the warning returns on the first drive. Set the pressures before the setting runs, because a soft tyre changes the height at that corner and the module learns the wrong position.

Check the beam pattern against a wall at the distance the maker states, then road test the car in the dark and watch the beams follow the wheel. Write the basic setting result and the beam height on the sheet, since the customer judges this repair with the lights on at night.

Handback and the night test

Refit the trim, clear the memory and cycle the ignition three times, watching the warning at each key on. Then drive the car at night on a road with a bend and confirm that the beams turn with the wheel. A repair that passes in the bay and fails on a bend has a motor that stalls under load.

Write the sensor values from both axles on the sheet along with the basic setting result. That record is what makes a return visit short, since these faults come back after a suspension repair and the numbers from the first visit show whether a sensor has moved.

Read both sensor values before you take a wheel off, because one axle sitting at the end of its range explains the warning and the low beams in one look. Then measure the reference voltage with the sensor connected, since a sensor that pulls the reference down makes the module report both axles and sends you to a part you do not need. Finish with the basic setting on level ground and a drive in the dark, because a beam that never moves on a bend means a motor that stalls and the customer will see it on the first night.

What is measured on an A8 or a Q7 with the adaptive light warning
SymptomLikely causeWhat is measured
Warning at key on, beams lowAxle sensor not reportingBoth sensor values on the data page
One axle reads far from the otherBent arm or worn elementSignal wire while the body is pushed down
Both axles reported at onceReference pulled lowFive volt reference at the sensor plug
No movement on a bendHeadlight motor or its driveMotor drive on the scope during basic setting

Frequently Asked Questions

Can the car be driven with the adaptive light warning?

It can, and the beams stay in a fixed position that is low. The car is safe to move in daylight and the fault is read before the lamps are touched.

Why do the headlights point at the ground?

The module parks the motors in a safe position when it has no usable sensor value. The beam comes back up once the sensor reads and the basic setting has run.

Does a replacement module need coding?

It is coded to the car and the basic setting is run afterwards on level ground. The label is photographed first, since the coding is written from that page.

Can a sensor be repaired?

A bent arm or a link that has come off its ball is refitted and the basic setting is run. A worn track inside the sensor is a replacement, and the two are told apart by watching the signal as the body moves.

Related Services