An ABS lamp on a Golf 5 or a Passat B6 with an entry about the pump motor usually points at a relay inside the hydraulic unit. The unit is fed by two heavy cables and it switches the pump itself, so the test is a direct feed at the motor and a look at what the unit does with it. Measure before the unit comes off the car.
The ABS lamp and the traction lamp stay on after the engine starts and the driver reports no other symptom. On a wet road the brakes work as ordinary brakes, and the pedal feels normal. Write down whether the lamps come on at key on and stay, since a lamp that comes on after a few metres points at a wheel sensor. Check the brake fluid level as well, because a low level sets a lamp of its own and the driver reports one lamp whichever one it is.
Read the memory and note the entry word for word, because one entry names the pump motor and another names a sensor. Ask about a recent brake service and about a battery that was replaced, since both disturb the unit and leave a stored entry that comes back after a clear.
Read the ABS address and save the memory before anything is cleared, then read the coding from the identification page. The unit is coded to the car and a replacement is prepared from that page. Photograph the label on the unit before it comes out of the bracket. Note the software level on the same page, since a unit with different software takes a coding that this car will not accept.
Check the live values for the four wheel speeds while the car is pushed a few metres, because a sensor that reads zero at one corner sets a lamp that looks like a unit fault from the driver seat. A car with four equal speeds and a pump entry has a fault inside the unit or on its heavy feed.
The unit has two heavy feeds at its connector, and each one is protected by its own fuse. Measure both at the plug with the ignition on, then load each one with a bulb and read again. A feed that holds battery voltage open and falls under a bulb has a fuse holder or a joint that will not carry the pump. Look at both fuse holders for a brown stain, because a fuse that has run warm for a year leaves a mark on the plastic around it.
Measure the ground pins to the battery post on the millivolt range, and measure the ground cable at the unit bracket as well. A drop above about fifty millivolts during a pump run leaves the motor short of current and the unit stores an entry that reads like an internal fault. Clean the stud and repeat the readings.
Unplug the unit connector and feed the pump motor from a fused lead at the motor pin, then listen for the pump. A pump that runs on a direct feed has proved the motor and the hydraulic side, and the fault sits with the switching inside the unit. Keep the feed on for a second only, since the pump is not made to run dry for long. Have an assistant listen at the hydraulic unit while you touch the lead on the pin, because the pump is quiet and the sound carries through the bracket.
Measure the current the motor draws on that direct feed and write the number down, because a motor that pulls far more than the maker figure is on its way out and a new relay will not save it. A motor that draws nothing has an open winding and the unit is replaced.
The pump is switched by a relay on the board inside the hydraulic unit, and the contacts take the full motor current every time the ABS works. A relay with burnt contacts closes and passes almost nothing, which is why the pump stays silent while the unit reports the motor as faulty. Compare the resistance across the contacts with a new relay, because a contact that has burnt reads high and the difference is easy to see.
The unit is opened on the bench and the relay is replaced, then the board is checked around the contacts for heat damage. A board with a lifted track at the relay is repaired as well, since a new relay on a damaged track fails again within weeks. Photograph the board before and after the work.
Even with a pump entry, measure the four sensors and their plugs before the unit comes off, because a car can carry two faults and the second one shows after the first is repaired. Look at the sensor plugs for water and for a wire that has rubbed through on the strut. Read the speeds while the car rolls down a gentle slope with the ignition on, since a push by hand is often too slow for the unit to report.
Check the harness from the unit to each wheel for a chafed wire near the suspension, since a short there disturbs the unit and produces entries that move between addresses. Wiggle the harness while the tester reads the speeds, and write down which corner drops out at which movement.
After a unit is fitted, code it to the car and run the basic setting for the steering angle sensor on a level surface with the wheel straight. Then drive the car and let the unit learn the wheel speeds. A unit fitted without that work keeps the lamps on and the driver brings the car back the same day. Keep the wheel straight while the setting runs, because a setting taken with the wheel turned stores an angle that pulls the car to one side.
Read the memory after the coding and clear it once, then cycle the ignition and read it again. A unit that stores nothing has been coded correctly. Write the coding value and the basic setting result on the sheet for the next reader.
Refit the unit and bleed the brakes at the calipers, then check the pedal for a firm feel before the car moves. Drive on a quiet road and brake hard enough to bring the ABS in, because a pump that runs on a direct feed and fails under a real stop has not been repaired.
Write the two feed values and the motor current on the sheet, along with the coding result. That record is what makes a return visit short, since these units come back after a battery change and the numbers from the first visit show whether anything has moved.
Read the four wheel speeds before you take the unit off, because one dead sensor sets a lamp that the driver reports as an ABS fault and the pump entry is a stored record from an old event. Then feed the motor directly at the plug, since a pump that runs on that feed proves the motor and sends you to the relay inside the unit. Write the motor current down as well, because a motor drawing far more than the maker figure will burn a new relay and the customer will be back within the month.
| Symptom | Likely cause | What is measured |
|---|---|---|
| ABS lamp with a pump entry | Relay inside the unit | Pump on a fused direct feed at the motor pin |
| Lamp after a few metres | Wheel sensor signal | Four speeds while the car is pushed |
| Pump runs and draws heavy current | Motor seizing | Current on the direct feed against the maker figure |
| Lamps on after a unit is fitted | Coding or basic setting | Coding page and steering angle setting |
The brakes work as ordinary brakes and the ABS does not operate, so the car is brought in. The pedal feels normal and the driver often waits, which is why the pump entry is read on the tester while the pedal says nothing.
The relay inside the unit switches the motor, and burnt contacts close without passing current. The direct feed proves the motor and leaves the relay as the fault.
It is coded to the car and the steering angle setting is run afterwards. The identification page is photographed before the old unit comes off, since the coding is written from it.
The unit is opened and the relay is changed, and the board around it is checked for heat damage at the same time. A new relay on a lifted track fails again within weeks.