The car is parked level in the evening and sits on its bump stops by the morning, and the pump lifts it again as soon as the engine runs. On the W221 the ABC system holds the car up with hydraulic pressure, so a car that sinks is losing fluid past a seal somewhere in the circuit. The order below finds that leak without exchanging parts on a guess.
The driver reports a car that drops overnight, usually on one corner, and a warning about the suspension level on the dash after the first start of the day. Sometimes the car lifts itself within seconds and the driver thinks nothing of it, which is why the fault is often months old before it is looked at. Ask which corner drops, since that answer divides the circuit in half. A car left on a slope drops on the corner carrying the least load, so where it is parked changes what the driver sees.
Ask whether the car drops while it is parked for an hour as well as overnight, and whether the pump runs longer than it used to when the engine starts. A pump that works harder on every cold start has been chasing a leak for a while. Write both answers down, then look at the car before it is started.
The system keeps the car at ride height with oil pressure from an engine driven pump, and each corner has a strut with its own valve in a block. A pressure reservoir smooths the supply and holds the car up while the pump catches up. Fluid is lost only through an external leak or past an internal seal inside a valve or a strut.
The reservoir is charged with nitrogen behind a diaphragm, and when that charge is gone the system works harder and rides harshly over small bumps. A car that sinks and rides badly has more than one fault in the same circuit. Read the fluid level in the reservoir before the engine starts, since a low level is the first sign of a slow leak. Mark the reservoir with a scribe once the car is at height and warm, so the drop is visible next morning.
Turn the ignition on without starting the engine and read the four height values on the tester, then compare them with the values the car shows when it is lifted and level. A corner that reads far below the others has given you the leak and the corner in one reading. Write all four numbers on the sheet before the pump runs.
Measure the height at the wheel arch with a tape from the ground to the arch on each corner as well, because a sensor that lies will make the tester and the tape disagree. A tape reading that is even on all four corners with a low value on the tester points at the sensor and its linkage. That fault makes the car sit low without losing a drop of fluid.
Dry the struts and the valve blocks with brake cleaner, and wipe the lines as you go. Let the car stand overnight on clean paper, since a leak that shows as a damp patch under one corner has named the strut and saved the pressure test. Look at the hose crimps as well, since a weeping crimp leaves a stain that a wet strut hides.
Look at the reservoir level again after the car has stood, and compare it with the mark you made when it was warm. A level that has fallen with no puddle under the car is going into a strut boot or past a valve into the return. Squeeze each strut boot with a gloved hand, because a boot holding oil is a shaft seal on its way out. A leak that leaves no trace on the floor is the one that takes the longest to find.
Connect a gauge to the system test port, run the engine until the car is at ride height and switch off. Watch the gauge for ten minutes with the ignition off. A pressure that falls away steadily is a leak in the circuit, and a pressure that holds leaves the fault with a valve that lets oil past when the car is loaded. Keep the key away from the car and the doors shut during the test, since a system that wakes to correct itself will spoil the reading.
Note the pressure the pump reaches when the car is lifted from its stops, since a pump that cannot reach its figure is worn and the whole circuit has been running slow. Compare that figure with the one the tester shows for the pressure sensor. A gauge and a sensor that disagree send you to the sensor before the pump.
Cap the line to one strut at the valve block and lower the car onto its wheels. Leave it overnight, then read the height of that corner in the morning. A corner that holds with the cap in place has named the strut, and a corner that drops again has named the valve. That test needs no parts and it decides the job.
Work one corner at a time and write the result down each morning, because a car with two faults will confuse you if you test them together. Keep the caps clean and cap the line ends, since dirt in this circuit ends up in a valve seat. Do not run the engine with a line open to the air.
Test the reservoir charge where the tester offers the function, and replace it where the charge is gone, since a system without that reserve works the pump to its limit on every correction. A tired reservoir also makes the car drop as soon as the engine stops. The reservoir is worth replacing before the pump is suspected.
Listen to the pump at idle with the car at height, since a pump that whines as it works has been asked for pressure it cannot hold. Check the belt that drives it for slip as well. A pump that is worn will not hold the car up overnight even with a perfect circuit behind it.
The leak is confirmed when the height values show one corner down, the tape agrees, the gauge falls with the ignition off and the capped corner holds overnight. Those results together name the strut or the valve, and the part is ordered with the numbers on the sheet in front of you.
Write the four heights and the gauge figure on the sheet, then add the result of each cap test, because a car that comes back with the same complaint needs that history. Bleed the circuit by running the system through its full travel twice before the car goes back. Check the fluid level again after a week of use, then drive it over a rough surface and listen for a knock at the corner you worked on.
Read the four heights with the ignition on and the engine off, because a car that is already lifted tells you nothing. Dry the circuit and let it stand on paper, then hold a gauge on the test port with the ignition off. A corner that drops again with its line capped has named the valve, and the reservoir is tested before the pump is blamed.
| Symptom | Likely cause | What is measured |
|---|---|---|
| One corner down in the morning | Strut seal or a valve | Four height values before the engine starts |
| Whole car down, pump runs long | Reservoir charge or a leak | Gauge on the test port held with the ignition off |
| Car sits low, no fluid lost | Level sensor or its linkage | Tape at the arches against the tester values |
| Corner holds with the line capped | Valve block letting oil past | Height of the capped corner after a night |
The system corrects itself when the engine starts, so a small settle is expected after days of standing. A car on its stops after one night is losing pressure.
It can be driven while the pump keeps up, and it should not be driven once the warning appears and the car sits on its stops. The circuit is tested before the car is used again.
The strut is mechanical and carries no coding, so a good used one works. The system is bled afterwards and the heights are read again with the engine running.
The car is left overnight and the four heights are read before the first start. A corner that has dropped again means the cap test was read wrong or a second fault sits behind it.