A W212 that stays in one gear and refuses to shift after a hot restart has usually lost a speed signal from inside the gearbox. The 7G-Tronic keeps its control unit on the conductor plate in the sump, together with the sensors that report shaft speeds. Read the data page before the pan comes off, because the sensors tell you which way the job goes.
The driver reports a car that drives in one gear and will not shift, often after a stop at a shop with a hot gearbox. The cluster may show the gear as it was, and the selector still moves. Write down whether the fault appears only when hot and whether a restart clears it for a while, since that pattern points at a sensor that fails at temperature. If the fault appears only after a long drive, the plate has reached the temperature where a sensor stops reporting and the cold test will pass.
Ask about the last gearbox service and about any work on the wiring near the box, because a plug that was disturbed during a service behaves exactly like a failed plate. Ask as well whether the car has been driven through deep water, since the connector at the box sits low and it takes water from the road.
Read the transmission address and save the memory before anything is erased, then note which of the speed sensors is named. A car with one sensor entry and a fixed gear has a signal missing, and a car with several entries at once has a supply or a ground problem common to them. Write the entries out in the order they were stored.
Read the coding and the identification page as well, because the plate carries the coding for the gearbox variant and a replacement is ordered from that page. Photograph the label on the unit before it comes out. A plate fitted with the wrong coding shifts badly and stores entries of its own on the first drive.
Pull the connector at the gearbox and look for oil inside the plug and on the pins, because oil travels along the harness from the sump and reaches the control unit from the inside. A plug with oil on the pins is a fault of its own and it explains entries that come and go. Replace the adapter and clean the harness before you condemn the plate. Smell the oil on the plug as well, because burnt fluid on the pins points at a box that has been hot and at a plate that took the heat with it.
Check the harness above the plug for oil as far as you can reach, since oil that has climbed the wires keeps arriving at the pins after a new adapter is fitted. Wash the section with a contact cleaner and dry it with air. A second adapter fitted over wet wires leaks again within a few weeks.
Start the engine, select D and hold the car on the brake, then read the three shaft speeds on the same page. Each value should be present and they should make sense against each other at idle. A sensor that reads zero while the car is in gear and the engine runs is not reporting, and the box goes to a fixed gear to protect itself. If the unit reports a speed for one shaft and nothing for the others, the plate is the suspect before any wiring is touched.
Repeat the readings with the gearbox hot, because a sensor that fails at temperature often reads perfectly on a cold car. Let the car idle for several minutes and watch the values as the oil warms. A value that drops out at one point of that warm up names the sensor and the plate it sits on.
Measure the feed at the gearbox connector with the ignition on, then load it with a bulb and read again. A feed that holds battery voltage open and falls under a small load leaves the plate without the current it needs, and the entries that follow look like sensor faults. Note the loaded value on the sheet. Check the fuse for the transmission control unit in the same panel while the meter is out, since a fuse that has run warm leaves a mark on the plastic around it.
Measure the ground at the box to the battery post on the millivolt range with the ignition on. A drop above about fifty millivolts upsets the sensor signals and produces entries that move from one sensor to another between drives. Clean the earth point on the box and repeat the readings before the pan comes off.
With the pan off and the plate exposed, measure the resistance of each solenoid at the plate connector and compare the values with the maker figures. A solenoid that reads open or very low has failed, and it is replaced with the plate on this gearbox. Look for a smell of burnt oil and for metal on the magnet, since those two findings change the repair.
Look at the plate for a cracked track and for a sensor that has lifted from the board, because the plate is a circuit board in hot oil and the joints take years of heat. A plate with a visible crack is replaced, and the box is checked for the cause of the heat before the new part goes in.
The plate is the fault when a shaft speed is missing on the data page, the plug is dry, the feed holds under load and the ground drop is low. Those results leave the wiring out of the picture. Write each value down as you take it, since the coding of the new plate is written from that sheet.
A box with one speed missing and every other value correct takes a plate, and a box with all three missing at once takes a look at the feed and the ground before any part is ordered. That order saves a plate on a car with a tired relay.
Fit the plate with a new pan gasket and fill the box with the fluid the maker lists, then code the plate to the car and reset the adaptations. Check the fluid level at the temperature the maker states, with the engine running and the selector in P. Write the level and the coding result on the sheet.
Drive the car through every gear with the tester connected and watch the three speeds against each other, then let it idle hot and read the memory again. A box that shifts cleanly and stores nothing after that drive has been repaired, and the customer gets the car back with the adaptations learned on a real road.
Read the three shaft speeds before the pan comes off, because a single missing signal sends you to the plate and three missing signals send you to the feed and the ground. Then pull the plug and look for oil, since a wet connector explains entries that move around and it is a repair you can do without opening the box. Write the hot readings down as well, because a sensor that fails at temperature passes every cold test and the customer will be back within the week.
| Symptom | Likely cause | What is measured |
|---|---|---|
| Fixed gear after a hot restart | Shaft speed signal missing | Three speeds on the data page, engine idling in D |
| Entries that move between drives | Oil in the connector | Plug and pins at the gearbox |
| Several sensor entries at once | Feed or ground at the box | Loaded feed and millivolt ground drop |
| Harsh shifts after a repair | Plate not coded | Coding page and adaptation reset |
It moves in one gear and it will not hold a high speed for long, so it is brought in. The box protects itself and driving it far heats the oil that the plate sits in.
The control unit starts again and finds the sensor working until the oil reaches temperature. That pattern is the reason the readings are taken twice, once cold and once hot.
It is coded to the car and the adaptations are reset afterwards. The identification page is photographed before the old plate comes out, since the new one is ordered from it.
The adapter is replaced and the harness is cleaned and dried before the new part goes on. Oil left on the wires climbs back to the pins and the fault returns.