PGE Tuning Lab

Mercedes 722.9 speed sensor circuit, read from the plate up

A Mercedes with the 722.9 box that slams into a gear and refuses to shift further is usually reporting a speed signal it can no longer read. The sensor sits inside the box on the conductor plate, and the circuit reaches it through the plate and the connector. Continuity is measured at the plate before anything is replaced.

What the driver feels when the speed signal is lost

The box holds a gear and refuses the next one, or it engages with a jolt and then limits itself to a fixed ratio. The cluster may show the gear but the box behaves as if the car were standing still. That pattern is a missing speed signal rather than a worn clutch pack.

Ask whether the fault appears when the oil is cold or only after a long drive, because the answer points at a solder joint or at the plate itself. A box that fails from the first minute of a cold start behaves differently from one that gives up after twenty minutes of driving.

Reading the codes and the live values first

Read the gearbox address and look at the live speed values with the car moving on a lift or on the road. If the input speed reads zero while the output speed reads correctly, the sensor on that side is the suspect and the circuit is measured at the plate.

Note the oil temperature at the moment the values drop, because a reading that fails only when the box is hot points at a joint that opens with expansion. Clear the codes and repeat the road test so you see which entry returns first rather than which entry was stored oldest.

The speed sensor circuit inside the box

The sensor is mounted on the conductor plate inside the box, in the oil, and its signal leaves through the plate and the round connector on the casing. Every one of those connections carries a small signal, so resistance that would not matter on a lamp matters here.

The circuit is measured from the connector pins down to the sensor terminals on the plate, with the box drained and the pan off. You are looking for continuity with a very low resistance and for no path to ground, because either fault removes the signal without damaging the sensor itself.

Measuring plate continuity

Put one probe on the plate terminal and the other on the matching connector pin, and read the resistance with the meter on its lowest range. A value that wanders as you move the loom is an intermittent joint and not a sensor. Repeat each reading twice before you believe it.

Check the plate where the conductor runs bend, because that is where heat cycling opens a track. Look at the track under magnification as well, since a hairline crack can measure continuous cold and open when the box is at working temperature. Flex the plate gently while the meter is connected.

Ruling out the connector and the harness

The round connector on the casing takes oil and heat, and a pin that has gone green there gives the same fault list as a failed plate. Open the connector and look at the pins before the pan comes off, because that check costs nothing and explains a share of these cases.

Measure from the connector pin to the gearbox control unit plug with the box still assembled, and compare the value with the plate reading. A circuit that is good at the plate and poor at the unit plug puts the fault in the harness between them, which is a different repair.

Oil and temperature effects

The box runs hot and the plate sits in the oil, so every measurement taken cold is only half the story. Repeat the continuity check with the box at working temperature, using the oil temperature value from the tester as your reference rather than a guess.

When the reading is stable cold and open when hot, the plate is the fault and the repair is on the track. When the reading is poor at both temperatures, the joint or the sensor terminal is the fault and the plate is not disturbed.

What the plate test confirms

A plate that shows continuity at both temperatures and no path to ground clears the circuit, and the search moves to the sensor itself or to the unit. A plate that opens when hot confirms the fault without any doubt, and the repair is planned from that measurement.

After the plate is replaced the box is filled to the stated level at the stated temperature with the engine running, then the adaptations are cleared and relearned on a road test. Watch the speed values again on that test, because they are the proof the circuit is back.

Handing the car back

Drive the car through a full warm up with the tester connected and watch the speed values and the shift quality as the oil reaches temperature. A box that reads both speeds and shifts cleanly through the warm up has been repaired at the circuit, which is what the sheet should say.

Write the resistance values you measured at the plate, cold and hot, so the next reader has a comparison. Tell the owner how the car behaved on the road test, because a box that still hesitates after the repair needs the adaptations read again before anything else.

Use the same reference for every measurement you take on this gearbox, and write the values down. Measure the conductor resistance from the plate connector to the sensor pin, then the same conductor again with the harness moved by hand along its length. A reading that changes while the harness moves is a broken strand inside the insulation, which no fault code will ever name, and it explains the intermittent limp mode far more often than the speed sensor plate itself does.

What is measured when the 722.9 loses its speed signal
SymptomLikely causeWhat is measured
Box holds one gear and refuses the nextSpeed signal missing at the plateContinuity from plate terminal to connector pin
Fault only after a long driveTrack open when hotPlate resistance at working temperature
Input speed reads zero, output reads fineSensor terminal on the plateResistance and path to ground at the sensor
Fault after work on the boxRound connector pin gone greenPin condition at the casing connector

Frequently Asked Questions

Can the plate be tested with the gearbox in the car?

The connector pins are reached with the box in place, and the plate itself needs the pan off. Both readings are taken with the meter on its lowest range, and each one is repeated before it is believed.

Why does the fault only appear when the box is hot?

A track or a joint opens as the plate expands, so a reading taken cold shows continuity while the car drives fine. That is why the measurement is repeated at working temperature.

Is a speed fault always the sensor?

No, the sensor sits at the end of a circuit that runs through the plate and the connector, and resistance anywhere on that path removes the signal. Continuity is measured before any part is ordered.

What is done after a plate is replaced?

The box is filled to the stated level at the stated temperature with the engine running, then the adaptations are cleared and relearned. The speed values are watched again on the road test.

Related Services